The Accurate Reloading Forums THE ACCURATE RELOADING.COM FORUMS Guns, Politics, Gunsmithing & Reloading Gunsmithing 44 Mag Case SeperationGo | New | Find | Notify | Tools | Reply | |
| 44 Mag Case Seperation | Login/Join |
| One of Us |
Yesterday I had a 44 mag case separate in a Contender barrel. The case head and about 3/8 inch of the case extracted as normal but the remaining portion of the case stayed in the chamber. Over the years this has happened a couple of times and I have removed the case by inserting a 45 bore brush into the chamber, turning slightly and the brass came right out. I tried the same thing and this time it didn't work. Any ideas? Thanks and Regards Keith | ||
|
| One of Us |
Shove a new .45 cal brush in and pull straight back. Or fill the chamber and case with Cerro safe or equivalent chamber casting alloy. Make sure you get the metal cast over the edge of the case mouth. As soon as it hardens tap it out. Once you get the low temp alloy out melt it so you can remove the case and reuse the alloy. | |||
|
| One of Us |
I have a pipe tap welded to a flexible packing puller I use for this. It stays in my range box and has bailed me and quite a few others out over the years! | |||
|
| one of us |
This.^^ Interisting Of the many 10s of thousands of straight walled pistol cases I reloaded. I have had hundreds crack length wise never one that cracked leaving part of the case in a chamber | |||
|
Moderator |
6" of coat hanger, fold one end over 90 deg, and hook the case mouth .. use alum or copper of worried about scoring the chamber ,, 5 second fix opinions vary band of bubbas and STC hunting Club Information on Ammoguide about the416AR, 458AR, 470AR, 500AR What is an AR round? Case Drawings 416-458-470AR and 500AR. 476AR, http://www.weaponsmith.com | |||
|
One of Us |
You have excessive headspace...... | |||
|
One of Us |
X 2 Never mistake motion for action. | |||
|
| one of us |
" I have a pipe tap welded to a flexible packing puller I use for this. It stays in my range box and has bailed me and quite a few others out over the years! " Nice thought, but I saw a Winchester Model 43 in 22 Hornet last month that had this really nice spiral groove in the rear of the chamber from the tap. Customer ruined a great gun. I have seen my share of ruined chambers also from Ice Picks, and knifes. Either a new bore brush, or like Jeff said a 90 degree tool form something softer than the barrel. My 2 cents J Wisner | |||
|
| One of Us |
The idiot should have measured the OD of the case and uised a tap smaller than that. Jim Kobe 10841 Oxborough Ave So Bloomington MN 55437 952.884.6031 Professional member American Custom Gunmakers Guild | |||
|
| One of Us |
All types of idiots do own, and try to work on, guns. At least around here they do. Often with negative results. I have trained most of them, not to F with it; bring it to me intact; not all the parts loose in a box with some of them heated up and bent, or twisted. Etc. Here's one; last month; "My bolt was a bit tight in my Mauser so I took two propane torches and heated it up and twisted it a little; it didn't work so I twisted and beat on it more". He heated the thing cherry red all over and twisted it in several places. It was assisted and witnessed by someone who knew better but helped anyway. I sold him a new receiver. I should write a book on it. No time. I waste enough time here on AR. | |||
|
| One of Us |
And just like that, another 'custom mauser' was birthed. | |||
|
| One of Us |
Friend done this. I made an expanding collet sort of too and put fine teeth on it with an 18 tooth per inch checking file. Told him put it in the case and tighten to expand it and knock out the case and assembly with a cleaning rod. Viola!! | |||
|
| One of Us |
Kind of a no brainer I'd think.....but I know a lot of "no brainers", they can be fun to watch! | |||
|
| one of us |
Or firing #97 on that case    | |||
|
| one of us |
This is true of a lot of things in life. I was chatting yesterday with a friend I have had since 3rd grade; he drives an 18 wheeler, and was talking about how milk sloshes around in the tank because it can't have baffles or compartments. He then said, "It is a bit tricky when you are driving in snow..." We all know how to drive, but unless we drive an 18 wheeler we aren't likely to be able to keep one out of the ditch, to say nothing of being able to back it up to a loading dock. Same logic applies to gunsmithing. | |||
|
| One of Us |
Like the man said, "Just because I have a garage, doesn't make me a car." Never mistake motion for action. | |||
|
| One of Us |
AZ: I used to haul heavy equipment over the road. Pumps failed on a 11,000gal water wagon about half full. Instead of pulling the plug, they shipped it on my rig from Kans to Cal. I couldn't get under it loaded to access the drain plug. Took my pistol and shot about 20 holes thru it they could weld a small patch over it. Owner sure was pissed about the freight bill for all that water. Happy I tried to get it drained. "no problem with the bullet holes, we can patch those easy". That damned thing would rock around for ten minutes after I parked just from the water sloshing around. A few years after that I operated one on a construction job. Sure enjoyed that! George "Gun Control is NOT about Guns' "It's about Control!!" Join the NRA today!" LM: NRA, DAV, George L. Dwight | |||
|
| one of us |
I have another friend who drives a truck (or as they say "who drives truck"); he is married to the woman who does MsAZWs pedicures and we have become friends. He and my pal have the same vital attribute: they tolerate dickheads on the road without even breaking a sweat. | |||
|
| Powered by Social Strata |
 | Please Wait. Your request is being processed... |
|
Visit our on-line store for AR Memorabilia