THE ACCURATERELOADING.COM BIG BORE FORUMS

Accuratereloading.com    The Accurate Reloading Forums    THE ACCURATE RELOADING.COM FORUMS  Hop To Forum Categories  Rifles  Hop To Forums  Big Bores    458 Lott Barrel contour question

Moderators: jeffeosso
Go
New
Find
Notify
Tools
Reply
  
458 Lott Barrel contour question Login/Join
 
One of Us
posted
What do you folks think of a #5 contour for a 458 Lott for a Montana rifle Company barreled action? Muzzle diameter is .700. Barrel length is 24 inches.


My biggest fear is when I die my wife will sell my guns for what I told her they cost.
 
Posts: 6654 | Location: Wasilla, Alaska | Registered: 22 February 2005Reply With Quote
One of Us
posted Hide Post
i built one a number 5 douglas contour. as light as some will go with a 45 cal. shot it the other day to regulate the standing leaf. i believe i sent you a picture of it.
max
 
Posts: 982 | Location: Shenandoah Valley VA | Registered: 05 January 2005Reply With Quote
one of us
posted Hide Post
I'd say that is perfect also.

#5 and 0.700" at the 24" muzzle would be as light as I would go and should balance well with no added weight in the butt.

#6 or up to 0.750" at the muzzle would be if you want it a bit heavier, and want to add weight to the butt.

For comparison note that some do go sportier.
SIGARMS builds the Prechtl actioned Magnum Mauser in .450 Dakota with a 25" long barrel that is 0.667" at the muzzle. CZ makes their .458 Lott and WinMag with a barrel of same length and muzzle diameters that I have measured from 0.666" to 0.670".
 
Posts: 28032 | Location: KY | Registered: 09 December 2001Reply With Quote
One of Us
posted Hide Post
Thanks for the input. As heavy as the MRC's are the barreled action will weigh close to 8 and add 2 1/2 for the stock. Just wanted to make sure the barrel was large enough.


My biggest fear is when I die my wife will sell my guns for what I told her they cost.
 
Posts: 6654 | Location: Wasilla, Alaska | Registered: 22 February 2005Reply With Quote
Moderator
Picture of jeffeosso
posted Hide Post
to be clear, you'll need to compare the #X contour measurements.. for example, a shilen #4 is generally a bit lighter than a douglas or pacnor, but their #5 is HUGE...


8# for action and 2.5 for stock? that's freaking HEAVY.. add another .75 pound for recoilpad, cross and axial bolts, bedding and stock finish, then 1.5# for scope and mounts, you are nearly 13# in a lott....

aim for 9.25to 9.75 before scope... its way easier to add 6oz than to remove it. if the stock fits you LOP, it'll work just fine


opinions vary band of bubbas and STC hunting Club

Information on Ammoguide about
the416AR, 458AR, 470AR, 500AR
What is an AR round? Case Drawings 416-458-470AR and 500AR.
476AR,
http://www.weaponsmith.com
 
Posts: 40106 | Location: Conroe, TX | Registered: 01 June 2002Reply With Quote
One of Us
posted Hide Post
I agree it will be a little heavier than I want but it is the smallest contour they will use on a 45 caliber. The 8 pounds for the barreled action was an estimate quoted to me by MRC. I hope it weighs less. The stock is supposed to weigh no more than 2 1/2 finished.
Does the 8 pound estimate for the MRC barreled action seem reasonable?

Correction: MRC just informed me weight will be 7.25 to 7.5


My biggest fear is when I die my wife will sell my guns for what I told her they cost.
 
Posts: 6654 | Location: Wasilla, Alaska | Registered: 22 February 2005Reply With Quote
One of Us
Picture of vapodog
posted Hide Post
quote:
Correction: MRC just informed me weight will be 7.25 to 7.5

my 404 is a #5 from MRC and it's no where as heavy as the original estimates.

The above quote is a lot closer to the truth.


///////////////////////////////////////////////////////////////////////////
"Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery."
Winston Churchill
 
Posts: 28849 | Location: western Nebraska | Registered: 27 May 2003Reply With Quote
  Powered by Social Strata  
 

Accuratereloading.com    The Accurate Reloading Forums    THE ACCURATE RELOADING.COM FORUMS  Hop To Forum Categories  Rifles  Hop To Forums  Big Bores    458 Lott Barrel contour question

Copyright December 1997-2023 Accuratereloading.com


Visit our on-line store for AR Memorabilia