THE ACCURATERELOADING.COM SHOTSHELL RELOADING FORUM

Go
New
Find
Notify
Tools
Reply
  
mec 600 jr. sizing problem
 Login/Join
 
hivelosity
one of us
Picture of hivelosity
posted
new to me mec, came without instructions. It will size low or med brass with out any problem.
but when I size high brass the case gets stuck in the sizing ring.
Tried polishing the sizing ring and using some lube on the brass also tried to adjust the die to only partial resize but it still sticks.so bad that I have to remove the ring and drive the case out with a doll rod. any comments or suggestions?
 
Posts: 2134 | Location: Ohio | Registered: 26 June 2000Reply With Quote
stepchild 2
one of us
posted Hide Post
I'd contact MEC. In a minute or less they can probably tell you what the problem is.
Have them send you a manual for your press. I've loaded a bunch of shells on MEC's(410, 28, 20 and 12ga) and never had any problems.

Stepchild


NRA Life Member
 
Posts: 1326 | Location: glennie, mi. USA | Registered: 14 July 2003Reply With Quote
hivelosity
one of us
Picture of hivelosity
posted Hide Post
thanks, I found a manual on line but it didnt go into any troubleshooting.
Ill give mec a call and see if they will help.
Dave
 
Posts: 2134 | Location: Ohio | Registered: 26 June 2000Reply With Quote
scr83jp
One of Us
posted Hide Post
quote:
Originally posted by hivelosity:
new to me mec, came without instructions. It will size low or med brass with out any problem.
but when I size high brass the case gets stuck in the sizing ring.
Tried polishing the sizing ring and using some lube on the brass also tried to adjust the die to only partial resize but it still sticks.so bad that I have to remove the ring and drive the case out with a doll rod. any comments or suggestions?
I started with a MEC 600 then moved up to a 650 but for sizing brass I bought a MEC Super Sizer for 12g,sold them I bought a Pacific DL366 12g progressive loader because my son & I were shooting 12g loads Wed nites plus Sat & Sun .I located a used Mec Super Sizer on ebay & bought it do all of my 12g brass bases to speed up reloading.As little as I shoot I could do it all with a Mec 650.
 
Posts: 1116 | Registered: 27 April 2006Reply With Quote
hivelosity
one of us
Picture of hivelosity
posted Hide Post
homerjust trying to figure out why this pres will not do high brass.
It belongs to my nephew, i lent him my sizemaster and now he wont give it back. HAHA clap
 
Posts: 2134 | Location: Ohio | Registered: 26 June 2000Reply With Quote
2354
new member
posted Hide Post
To resize high brass hulls on the 600JR you have to change the bolt on the decapping rod. You should have two and you need to use the longer one. If you don't have two contact MEC to get the proper one.

I hope this will help you.


Good Shooting
George
 
Posts: 10 | Registered: 13 March 2004Reply With Quote
hivelosity
one of us
Picture of hivelosity
posted Hide Post
thanks George, I tried that and it still sticks.
Dave
 
Posts: 2134 | Location: Ohio | Registered: 26 June 2000Reply With Quote
p dog shooter
one of us
posted Hide Post
I size high brass all the time on mine. It sounds like you need to do a bit more ajustment on the rod abd sizing die.
 
Posts: 20250 | Location: wis | Registered: 21 April 2001Reply With Quote
  Powered by Social Strata  
 


Copyright December 1997-2025 Accuratereloading.com


Visit our on-line store for AR Memorabilia