The Accurate Reloading Forums THE ACCURATE RELOADING.COM FORUMS Guns, Politics, Gunsmithing & Reloading Gunsmithing Bolt won't close on Mauser 98Go | New | Find | Notify | Tools | Reply | |
| Bolt won't close on Mauser 98 | Login/Join |
| One of Us |
The shroud and the safety is turned to much to where the shroud and the safety hits the stock. How do I fix the problem, The button I tried to push and turn the shroud, I need some help please. | ||
|
| One of Us |
I use a bench edge to push down the cocking piece then turn at the same time.Good Luck | |||
|
Moderator |
OH .. you mean the shroud TURNED? its a PITA .. and you can mark up your wood .. this should be a job for your local gun smith .. REALLY ...the first time i tried this, after not putting in the plunger and spring, I stuck a screw driver into my palm .. you need to pull the cocking piece back and then turn .. its NOT easy, and if you have installed a heavier spring, its harder ... if you MUST do it yourself, please take it out of the stock, and have lots of wd40 HANDY ... nothing strips off blue like blood opinions vary band of bubbas and STC hunting Club Information on Ammoguide about the416AR, 458AR, 470AR, 500AR What is an AR round? Case Drawings 416-458-470AR and 500AR. 476AR, http://www.weaponsmith.com | |||
|
| One of Us |
Thanks alot plainsman and jeffeosso, I just got it turned. Now it closes like it should. Thanks a Bunch again. | |||
|
| One of Us |
Here is a link to surplus rifle and how to recock the bolt. http://www.surplusrifle.com/sh...serboltfix/index.asp Rad NRA Benefactor Member | |||
|
one of us |
since I hate blood on my rifles I clamp the bottom of the cocking piece in the end of my vise and pull the bolt forward and turn. As usual just my $.02 Paul K | |||
|
one of us |
I have found that if you get the right grip on the shroud with one hand and bolt with the other you can twist and recock the bolt. It's more about getting the right grip, rather than sheer strength. Jason "You're not hard-core, unless you live hard-core." _______________________ Hunting in Africa is an adventure. The number of variables involved preclude the possibility of a perfect hunt. Some problems will arise. How you decide to handle them will determine how much you enjoy your hunt. Just tell yourself, "it's all part of the adventure." Remember, if Robert Ruark had gotten upset every time problems with Harry Selby's flat bed truck delayed the safari, Horn of the Hunter would have read like an indictment of Selby. But Ruark rolled with the punches, poured some gin, and enjoyed the adventure. -Jason Brown | |||
|
| One of Us |
this is one of the faults of the 98 Mauser as cmopared to a later design, the 1936 Mexican, which put the knurled end on the cocking piece so that you wouldn't have to go through all of that B.S. to get it recocked. | |||
|
| One of Us |
has anyone ever tried to add a knurled knob to a std.98 cocking piece. i've soft soldered a cap on one of my cocking pieces to pretty up the end of the bolt and it worked fine and has stayed on for 15 or more years so far. the cocking piece was left polished white for obvious reasons. i would think a low temp silver solder could be used and still be strong enough for the intended use. it's just a matter of turning a decent looking little knob. | |||
|
| Powered by Social Strata |
 | Please Wait. Your request is being processed... |
|
The Accurate Reloading Forums THE ACCURATE RELOADING.COM FORUMS Guns, Politics, Gunsmithing & Reloading Gunsmithing Bolt won't close on Mauser 98
Visit our on-line store for AR Memorabilia