THE ACCURATERELOADING.COM GUNSMITHING FORUM


Moderators: jeffeosso
Go
New
Find
Notify
Tools
Reply
  
Looking for Trap door Buttplates
 Login/Join
 
one of us
posted
Can anyone help me find a source for checkered trap door steel buttplates. I am looking for the older style with the elongated 3 inch trap doors rather than the round hole type found on Springfields and Enfields.

Will be used on wood stocked centerfire rifles.

Thanks,

Rick
 
Posts: 494 | Location: Valencia, CA | Registered: 22 May 2004Reply With Quote
new member
posted Hide Post
When you find a source, let the rest of us know. Been looking for awhile myself.
 
Posts: 12 | Registered: 13 May 2004Reply With Quote
one of us
posted Hide Post
I will certainly do that my friend.

Numrich has a pretty large supply of the doors themselves and I bought ten of them in the event I have to end up making or adapting a plate. They only cost $2.15 each so if I screw it up I ain't out that much. They're pretty nice looking...three inches long by � inch wide and already checkered (page 1109 of their #26 categlog.)

It's pretty tough sometimes finding stuff when you want your rifles to be made from wood and steel rather that aluminum and plastic

Rick
 
Posts: 494 | Location: Valencia, CA | Registered: 22 May 2004Reply With Quote
one of us
posted Hide Post

rick,

try al and roger biesen @ biesen.com

show some checkered with the elongated trap.

hth.
bob
 
Posts: 475 | Registered: 16 December 2003Reply With Quote
one of us
posted Hide Post
A while back the NRA gunsmithing series featured a set of articles on making and installing your own traps and doors. I don't remember exactly which one had the articles and photos but if anyone had that set of books they may find the article. If not maybe a search of old bookstores will reveal the one.
Frank
 
Posts: 6935 | Location: hydesville, ca. , USA | Registered: 17 March 2001Reply With Quote
one of us
posted Hide Post
I like the pic on the biesen sight of the trap door UNDER the recoil pad. Then you get the best of both, the function of the trapdoor plus a pad in between the rifle and your shoulder. I don't know which one offhand, but there was a gunsmith I met and wrote the name of somewhere that has it setup to cut the holes in the butt of the stock for the cartridge the rifle is chambered in, puts the trapdoor buttplate over it and you get a few extra cartridges right there. I would like to see these setups in person.

anybody else got sources to find these?

Red
 
Posts: 4742 | Location: Fresno, CA | Registered: 21 March 2003Reply With Quote
one of us
posted Hide Post
Thank you very Bob...those plates from Biesen are exactly what I'm looking for.

I'll contact them tomorrow and will let you know how it works out.

Thanks again!

Rick
 
Posts: 494 | Location: Valencia, CA | Registered: 22 May 2004Reply With Quote
one of us
posted Hide Post

rick,

just remembered that new england custom gun carries a trap door butt plate thats made by recknagel of germany.
check out new england custom gun.com and recknagel.de
recknagel shows it under the german language site.

bob
 
Posts: 475 | Registered: 16 December 2003Reply With Quote
one of us
Picture of triggerguard1
posted Hide Post
See Rick, I told you that this was the place to come to find what you're looking for.

Glad to have you as a member of the board.

To all of those here contributing to this thread, Rick spoke with me a couple of days ago regarding this question and I directed him here. Another satisfied forum member.
 
Posts: 1021 | Location: Prineville, OR 97754 | Registered: 14 July 2002Reply With Quote
one of us
posted Hide Post
Thanks again Matt!

For anyone out there that hasn't had the pleasure of talking with Matt or doing business with him I would highly recommend doing both.

What a nice guy and helpful as hell. I ordered one of his steel triggerguard/floorplate assemblies for a Remington 700 I am building.

My other three 700's have D.D. Ross units on McMillan M40A1 fibergalss stocks but I'm building this one with a wooden stock and wanted a more traditional look for the metal.

I really don't believe that the extra weight and bulk of the D.D. Ross and the Badger units makes that much difference in the overall strength anyway. Matt assured me that his units are designed to fully withstand the force of torquing to 65 inch pounds and I think they are nicer looking to boot...not to mention a hell of allot cheaper!

Rick
 
Posts: 494 | Location: Valencia, CA | Registered: 22 May 2004Reply With Quote
  Powered by Social Strata  
 


Copyright December 1997-2023 Accuratereloading.com


Visit our on-line store for AR Memorabilia