Go ![]() | New ![]() | Find ![]() | Notify ![]() | Tools ![]() | Reply ![]() | ![]() |
one of us |
Depends on how you do the welding. It's certainly possible to add square bridges and re-heattreat the action, and after that much welding, I would consider it mandatory, at least on my rifles. - Dan | |||
|
<hsp223> |
Thanks for the reply. I was thinking along the lines of arc welding by laying beads to build up the bridges, allowing the action to cool between welds so as not to allow stress to build up. It's not fast but I'm in no hurry. Then use Tig to fill in the lettering. what type of rod would you recommend for welding. Thanks | ||
|
<JBelk> |
hsp223--- No NO NO!!! You can weld a square bridge to the rear with TIG and by making the bridge first then running a small bead around it, but if you try to lay on arc beads you're going to have a melted puddle of goo left over. Mausers are forged and have quite a bit of stress in them. If you weld on the front ring the threads will egg-shape and the recoil embuttments will be out of square......the action will be ruined. If you really want a front square bridge you need to make a sleeve that sweats on over the front ring with the square bridge made into it. | ||
|
one of us |
JBELK Any recommendations on gunsmiths/metalsmiths who can build a square bridge on mauser receivers? Also any that shorten military mauser receivers. Thanks | |||
|
one of us |
As Jack said, TIG is the only way to go on this. Seems to me I saw a Mauser done this way on this board not that long ago. Anyone remember? - Dan | |||
|
<JBelk> |
uwave--- I do both. Email me. | ||
|
<hsp223> |
Jack, Thanks for setting me straight on the welding. I just didn't think about the stresses already present. I have never seen a bridge sweated on a receiver before. I assume it is similar to the way the rear sight base is attached on military M98s. Does this increase the diameter of the front ring out of proportion? Thanks Hsp223 | ||
|
One of Us |
Jack, I remember seeing a 98 that John Hackley had square bridged. He built the front bases on a mill and had them kissing close and then tig welded them on. He then milled the edges so you couldn't tell. He had rigged up a 98 barrel with interupted threads in the top half and connected a garden hose to it and ran water through the action as he welded. I forgot about it until now. Nice to remember these things now that he is gone. He had it under his table at one of the shows at the Sands. He had a Winchster 63 that he had welded up scope base to and I was curious how he did it. He told me and then brought out the 98. [ 03-22-2003, 08:40: Message edited by: Customstox ] | |||
|
<JBelk> |
Chic--- I saw that one too........I have one in a box somewhere that didn't quite come out!! I prefer the treatment Ted Blackburn did on the #4 rifle. He surface ground the front ring of the P-17 and then sweated on a sleeve only .020 thick where it wraps around the receiver ring. It's very nearly impossible to see on a Mauser and you can make two at a time! | ||
|
one of us |
Very interesting Jack. You wouldn't happen to have pictures of this would you? - Dan | |||
|
<JBelk> |
Dan-- I emailed you the picture. I don't have it on my photo server and no way to get it there right now... Post it if you can. | ||
|
one of us![]() |
Have a look here: http://www.waffen-kaestel.de/e800.html Choose "Custom" and then take a closer view of the .270". These rifles aren�t real squarebridges, but some variations on the same theme - still worth seeing. Fritz [ 03-22-2003, 23:57: Message edited by: Fritz Kraut ] | |||
|
one of us |
Got the picture Jack. I just have to head out now, but I'll post it when I get back. - Dan | |||
|
one of us |
| |||
|
one of us |
http://ncmail.netscape.com/attachment/SW5ib3g=/115537/2/image/jpeg/base64/inline/#4P-17.jpg OK. I hope this works. - Dan | |||
|
one of us |
I can't see it; can anybody else? | |||
|
<JBelk> |
Try the picture HERE | ||
|
one of us |
Now that's what I was trying to do. Thanks Jack. - Dan | |||
|
Powered by Social Strata |
![]() | Please Wait. Your request is being processed... |
|
Visit our on-line store for AR Memorabilia