Intermediate length Mauser and 30-06 length cartridge?

The Accurate Reloading Forums

This topic can be found at:
https://forums.accuratereloading.com/eve/forums/a/tpc/f/9411043/m/312102155

10 October 2006, 00:56

skl1

Intermediate length Mauser and 30-06 length cartridge?

I'd like to make another rifle with a surplus Mauser action. I'm only finding intermediate length actions at the big 4 or 5 surplus houses (M24/47 Yugoslavian actions). Will a 30-06 length cartridge (i.e. .300WM, .338WM, .416 Taylor, etc) fit in these? If not, is the magazine box the limiting factor? If I replace the magazine box will it fit/work?

Thanks,

Steve

10 October 2006, 04:33

4t1mag

Better to use a VZ-24.for that length.Did use a
Yugo to build a nice .308.

10 October 2006, 05:01

RaySendero

My Vz-24 magazine maximum is 3.25". This limits the cartridge OAL to about 3.22 to 3.23" for good functioning.

10 October 2006, 05:13

jeffeosso

the 48 is what, .125 shorter than a standard? Z1R, i know you know, is that right?

if so, opening then form 3.15 to 3.35 is going to be a mild struggle.

unless you are doing the work yourself, buy a vz

jeffe

opinions vary band of bubbas and STC hunting Club

Information on Ammoguide about
the416AR, 458AR, 470AR, 500AR
What is an AR round? Case Drawings 416-458-470AR and 500AR.
476AR,
http://www.weaponsmith.com

10 October 2006, 06:04

craigster

I did a 48 in '06 once and wouldn't do it again. I used 150 or 165 gr round nose bullets seated deep enough to fit the magazine. It worked, but defeated the purpose. If I were to do it again, I'd go with a 308 or something in the "x57" family.

10 October 2006, 06:34

z1r

I agree with the others in that the action is not the best choice for the '06. I believe Jeffe is right that the action is about .125" shorter than a stadard 98. The magazines measure 3.230" while a standard 98 like the vz24 measures 3.310"

Interestingly enough, all the factory .30-06 ammo I've checked (not all for sure) measured less than 3.230" and will fit the magazine.

10 October 2006, 17:56

skl1

Thanks, all.

Steve

11 October 2006, 03:09

tsturm

quote:
Originally posted by RaySendero:
My Vz-24 magazine maximum is 3.25". This limits the cartridge OAL to about 3.22 to 3.23" for good functioning.

Get out your file

11 October 2006, 03:16

z1r

quote:
Originally posted by tsturm:
quote:
Originally posted by RaySendero:
My Vz-24 magazine maximum is 3.25". This limits the cartridge OAL to about 3.22 to 3.23" for good functioning.

Get out your file !

Don't you mean Dremel? hammering

11 October 2006, 03:21

Leo L.

The 6mm Remington is just right for these.

11 October 2006, 09:33

wildcat junkie

quote:
Originally posted by Leo L.:
The 6mm Remington is just right for these.

As is the 7X57, 257 Roberts and 6.5X55

15 October 2006, 17:14

RaySendero

I think I'd like to stuff a 9.3x62 in one.

16 October 2006, 07:49

James C Scott

What's the Oal for factory 9.3 X 62 ? I originally didn't think this would work, But if it does I may be making one. Thanks Ray....

(edited for stupidy)