THE ACCURATERELOADING.COM GUNSMITHING FORUM


Moderators: jeffeosso
Go
New
Find
Notify
Tools
Reply
  
lengthening bolt actions
 Login/Join
 
one of us
posted
Do you know of anyone who still sections and welds actions to lengthen them?I've seen a writeup in an older book about it and a local guy I know has shortened them, said it wasn't hard at all. He's a diemaker so he obviously knows what he's doing as far as machining.If the welding is kept to the rear of the action the lugs should be ok I assume, I'd think more people would be doing this as costly as big actions are and how limited your choices are for long cartridges. Thanks.
 
Posts: 93 | Registered: 14 October 2003Reply With Quote
one of us
Picture of ForrestB
posted Hide Post
quote:
Originally posted by wanna577:
I'd think more people would be doing this as costly as big actions are and how limited your choices are for long cartridges.


If you think magnum-length actions are expensive, just wait until you see the final bill on a "lengthened" standard action.

You can buy a magnum mauser clone for $2500, just about ready to stock. With a standard 98, you'd have to lengthen the action, plus the bottom metal, replace the trigger and safety, open the rails and polish. I'd imagine you'd have at least $2500 worth of cash or sweat invested by the time you get finished.

Since 375 length cartridges fit pretty easily in a standard 98 or M70, and 416 Rigby class cartridges really should have a larger diameter bolt, I don't see the benefit if lengthening an action in favor of buying a magnum clone these days.


______________________________
"Truth is the daughter of time."
Francis Bacon
 
Posts: 5052 | Location: Muletown | Registered: 07 September 2001Reply With Quote
Moderator
Picture of jeffeosso
posted Hide Post
I'm with forrest on this one....

unless the guy will do it for a song, it's going to rack up quick...

i could be done, and my ole buddy larry says

take two 98's,
cut one shorter than the other
wind up with a short and a long, once the work is done....

I think a fella could make TWO identical jigs, cut the actions with an abrasive wheel on a right angle head, swap front rings, and go from there.....

shesh, what a LOT of work...

then, of course, they'ld have to make a rig for the mags....
cn new floorplates....

trigger should work without change, though forrest..

jeffe


opinions vary band of bubbas and STC hunting Club

Information on Ammoguide about
the416AR, 458AR, 470AR, 500AR
What is an AR round? Case Drawings 416-458-470AR and 500AR.
476AR,
http://www.weaponsmith.com
 
Posts: 40016 | Location: Conroe, TX | Registered: 01 June 2002Reply With Quote
one of us
Picture of ForrestB
posted Hide Post
quote:
Originally posted by jeffeosso:
trigger should work without change, though forrest..



You're right. My only point there was that a new magnum mauser clone has a better trigger than a military mauser. Just trying to get an apples-to-apples comparison on the price.


______________________________
"Truth is the daughter of time."
Francis Bacon
 
Posts: 5052 | Location: Muletown | Registered: 07 September 2001Reply With Quote
One of Us
Picture of vapodog
posted Hide Post
quote:
I'd think more people would be doing this as costly as big actions are

Hey...good idea....get the necessary metalworking equipment, a shop and don't forget to ask your personal liability insurance man about the risk and go into business.....

In all seriousness this is simply not an economical thing to do. If it was there'd be a lot of folks doing it.....and there's not.


///////////////////////////////////////////////////////////////////////////
"Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery."
Winston Churchill
 
Posts: 28849 | Location: western Nebraska | Registered: 27 May 2003Reply With Quote
One of Us
posted Hide Post
There is one more big step you guys are missing. You have to do the same thing with the bolts, cut and weld as well as firing pins.


Chic Worthing
"Life is Too Short To Hunt With An Ugly Gun"
http://webpages.charter.net/cworthing/
 
Posts: 4917 | Location: Wenatchee, WA, USA | Registered: 17 December 2001Reply With Quote
one of us
posted Hide Post
I shorten Mausers (working on one right now-SR 98 that BARELY takes a .250-3000). Lenghtening is the same process. As posted earlier, it can delicately be called "labor intensive". The hours tend to run up, so you ahve to really want one. But some people only want a truly custom made just for them, and you can do it this way. From a pracitcal point, the GMA action is about $2200 US, and it is nice. But it is not made just for you. So horses for courses, but few people want to get on the fast one (ie-custom lengthened)
 
Posts: 2509 | Location: Kisatchie National Forest, LA | Registered: 20 October 2004Reply With Quote
One of Us
posted Hide Post
i did that a couple times, my advice is don't. I have a full machine shop at my disposal & it's a hell of a lot of work. If I had to charge myself for it i'd be broke
 
Posts: 13466 | Location: faribault mn | Registered: 16 November 2004Reply With Quote
  Powered by Social Strata  
 


Copyright December 1997-2023 Accuratereloading.com


Visit our on-line store for AR Memorabilia