The Accurate Reloading Forums
Stock Blank Choice For Custom Lott (photo)

This topic can be found at:
https://forums.accuratereloading.com/eve/forums/a/tpc/f/4711043/m/589102249

05 October 2008, 17:04
shootaway
Stock Blank Choice For Custom Lott (photo)
I just recieved word that my one of my two custom Lott projects is ready to stock.Here are two blanks selected.I like the one on the bottom.What do you think?[URL= ]a[/URL]
05 October 2008, 17:29
WVFred
Both are very nice blanks but I think I prefer the top one.

Fred


DRSS Member
05 October 2008, 17:47
maxbear
The top blank has a excellant layout.

I would not use the bottom blank. It has a "weak toe".
05 October 2008, 18:15
shootaway
quote:
Originally posted by maxbear:
The top blank has a excellant layout.

I would not use the bottom blank. It has a "weak toe".
Thanks maxbear.What is a "weak toe"?
05 October 2008, 18:17
jeffeosso
top one is a decent blank, bottom one should be cut into a 2 piece stock

you can do far better

www.hunterbid.com


opinions vary band of bubbas and STC hunting Club

Information on Ammoguide about
the416AR, 458AR, 470AR, 500AR
What is an AR round? Case Drawings 416-458-470AR and 500AR.
476AR,
http://www.weaponsmith.com
05 October 2008, 22:54
465H&H
It is hard to tell from the picture but it looks lie the lower blanks grain is not as straight through the fore arm as is the upper blank. The lower one may cause uneven pressure on the barrel as it drys.

465H&H
06 October 2008, 01:15
GarBy
One more vote for the top blank.....nice strong straight grain and it looks like a "Lott" stock. Bottom could be used for a lighter rifle or a 2 piece as was suggested.

Gary
DRSS
NRA Lifer
SCI
DSC
06 October 2008, 04:01
ShortandFat
Top stock for my choice
06 October 2008, 05:17
jkingrph
B weak toe, he means after blank is cut and finished, the grain at the toe will be at about 90 degrees to the buttplate . There will be such a short distance of straight grain across this area that it could break(split) very easily. Example, crosscut a very short piece off of a board, say one inch long and see how easily you can snap it with just your fingers.


JJK
06 October 2008, 08:32
The Slug
Save the lower one for a Ruger #1 or a shotgun. It's nice looking but the top one looks like a nice strong piece of wood.


-+-+-

"If someone has a gun and is trying to kill you, it would be reasonable to shoot back with your own gun." - The Dalai Lama
06 October 2008, 09:00
fredj338
For a Lott, go w/ the top blank. IMO there is too much figure in the bottom one at the pistol grip area.


LIFE IS NOT A SPECTATOR'S SPORT!
08 October 2008, 01:32
Andy E
I'm inclined towards the top one, but just to be sure I'd want to put my nose closer to look at the pores for grain flow, and not just the color lines. Is the bottom one black walnut?

Andy E
08 October 2008, 04:03
shootaway
I don't know what type of wood it is.I'll have to ask and find out.
08 October 2008, 04:41
katiesguns
The toe will break very easily and the wrist has too much North and South grain for a big bore. As stated earlier cut it into.Would make a very nice two piece. My vote is for # 1 and I think it will look mucy better than it alredy does once it is turned.
09 October 2008, 04:37
Gun toter
Holy Shit! I cannot believe no asked about the grain flow of the bottom blank. More to the point...what does the grain look like at the back of the blank.
If it is running north and south it does NOT have a "weak toe".
Further, it looks like the bottom blank can be reversed.
Without knowing all the details of the blank cutting it into a 2 pc blank is a bad move.

OYA, how dense and how heavy are these two????
Both of those two questions are just as prevalent as the layout.

And before you lay off on me, I worked for Winchesters custom shop turning wood for years.


I love my Avatar Too Fellas.
09 October 2008, 20:23
shootaway
Gun toter,I am honored!
09 October 2008, 20:28
Fjold
quote:
Originally posted by Gun toter:
Holy Shit! I cannot believe no asked about the grain flow of the bottom blank. More to the point...what does the grain look like at the back of the blank.
If it is running north and south it does NOT have a "weak toe".
Further, it looks like the bottom blank can be reversed.
Without knowing all the details of the blank cutting it into a 2 pc blank is a bad move.

OYA, how dense and how heavy are these two????
Both of those two questions are just as prevalent as the layout.

And before you lay off on me, I worked for Winchesters custom shop turning wood for years.


I was going to say, flip the drawing upside down on the bottom one and see how it lays out.


Frank



"I don't know what there is about buffalo that frightens me so.....He looks like he hates you personally. He looks like you owe him money."
- Robert Ruark, Horn of the Hunter, 1953

NRA Life, SAF Life, CRPA Life, DRSS lite

09 October 2008, 21:02
ACRecurve
Yep, the bottom blank looks like it could be laid out upside down. They both appear to be quarter sawn (which is my preference, but IMO makes little difference if bedded properly). I like the top stock better for color, though. Stock wood is a very personal choice...choose the one YOU like, Shootaway!


Good hunting,

Andy

-----------------------------
Thomas Jefferson: “To compel a man to furnish funds for the propagation of ideas he disbelieves and abhors is sinful and tyrannical.”