THE ACCURATERELOADING.COM BIG BORE FORUMS

Accuratereloading.com    The Accurate Reloading Forums    THE ACCURATE RELOADING.COM FORUMS  Hop To Forum Categories  Rifles  Hop To Forums  Big Bores    Thanks for the help! .450 Ackley

Moderators: jeffeosso
Go
New
Find
Notify
Tools
Reply
  
Thanks for the help! .450 Ackley Login/Join
 
<Timberghost>
posted
Much thanks to all who who helped advise me on my .450 Ackley sticking cases. The A-Square brass, although new, was crap! I purchased the Hornady basic magnum cases from Midway and loaded the 86 grains of IMR4064 with the 400 A-frames and they work great. The Hornady brass is much tougher! This is most evident in the forming die & trimmer.
As to DBBill's comment about me being "da man" for shooting a 6.5 pound .450 Ackley. I don't look like much of a man when I shoot it and tears form in my eyes, snot flies out my nose, and I have developed a "gravel" sound in my left shoulder when I move it. I don't know what the gentleman I purchased it from was thinking for building such a light gun in this caliber. Then again, he evidently didn't didn't know either because I only found 3 fire-formed cases in the 40 that came with the gun. However, as a left handed big bore nut, I must grin, squeeze the trigger, and "take the pain".
Thanks again to all who helped, Timberghost
 
Reply With Quote
Moderator
Picture of jeffeosso
posted Hide Post
NP..
Hope it shoots well...
I had a winchester 416 in their stock.. way too light, and I restocked it.

cheers,
and good hunting
jeffe
 
Posts: 40430 | Location: Conroe, TX | Registered: 01 June 2002Reply With Quote
<Timberghost>
posted
Jeffe,
I have been looking for a stock for this one, but again, LH anything is a bitch to find. [Frown] I may have to get a custom stock built for it. [Cool]
 
Reply With Quote
One of Us
Picture of ACRecurve
posted Hide Post
Timberghost,

Have you considered adding some lead or other weight to your rifle--3# or so would make ALOT of difference in recoil!

Good Hunting,
 
Posts: 6711 | Location: Oklahoma, USA | Registered: 14 March 2001Reply With Quote
<Timberghost>
posted
Recurve,
I was considering a mercury supressor, but the stock is a Brown Precision synthetic and there is no good way to bond it in. The back of the stock is hollow and filled with foam with a bonded Pachmar pad. Its so light that it would blow away in the breeze if the barrel and action were taken out.
 
Reply With Quote
one of us
posted Hide Post
6.5 lb for a 450 Ackley? Did you put it on the bathroom scale to verify the weight? I did not like the idea of a 12 lb 458 Lott but 6.5 lb is just way too light for this caliber. I am not sure about IMR 4064 powder but I use VARGET with Hornady's 500-grain RNSP in my 450 Ackley and I was shooting at around 2250 fps. Although this load is not bad at all for the shoulder, especially with a Triple X magnum pad but on the bench, the rifle recoils violently. I just cannot imagine shooting this load with your 6.5 lb rifle. Have fun.
 
Posts: 1002 | Location: Midwest USA | Registered: 01 September 2001Reply With Quote
  Powered by Social Strata  
 

Accuratereloading.com    The Accurate Reloading Forums    THE ACCURATE RELOADING.COM FORUMS  Hop To Forum Categories  Rifles  Hop To Forums  Big Bores    Thanks for the help! .450 Ackley

Copyright December 1997-2023 Accuratereloading.com


Visit our on-line store for AR Memorabilia