THE ACCURATERELOADING.COM MEDIUM BORE RIFLE FORUM

Accuratereloading.com    The Accurate Reloading Forums    THE ACCURATE RELOADING.COM FORUMS  Hop To Forum Categories  Rifles  Hop To Forums  Medium Bore Rifles    Accuracy. Free floating or fully bedded barrel?

Moderators: Paul H
Go
New
Find
Notify
Tools
Reply
  
Accuracy. Free floating or fully bedded barrel?
 Login/Join
 
One of Us
posted
Which way gets better accuracy and consistency? Fully bedded in wood with some up-pressure on the barrel at the tip of the stock, or free floating barrel?

Please state which you'd prefer on a plain'a game African rifle and the reason for your choice. Thanks



Don't Ever Book a Hunt with Jeff Blair or Blair Worldwide Hunting
http://forums.accuratereloadin...043/m/3471078051/p/1
 
Posts: 193 | Registered: 09 December 2014Reply With Quote
One of Us
posted Hide Post
yes..
they both work.

most of mine are bedded the full length of the stock [tang to forearm] and are hunting rifles.
I do it that way because they are going to get used and dinged and bumped and rained on and snowed on and dropped and banged into stuff.

somehow they manage to shoot groups under an inch day in and day out.

Varmint rifles I just bed from about an inch in front of the recoil lug back.

lighter weight barreled rifles seem to like some up pressure at the tip so I usually start with a glob under the tip and again under the recoil lug.
 
Posts: 5003 | Location: soda springs,id | Registered: 02 April 2008Reply With Quote
One of Us
posted Hide Post
Brian564, If you have a very stable wooden stock, you may have good success with full bedding. But, I’d likely float....just in case of some stock movement. With a synthetic ( in my case a McMillan)... I want full length. My thought, though possibly flawed... is “do not” leave any gap ( between barrel and stock). Any debris (particularly water potentially freezing), can create a pressure point, changing barrel harmonics, thereby possibly changing point of impact and/or group size!
My go to rifle (for “All” of my hunting) is a .375 AI which is capable of sub 2” groups at 300 yards....when I’m having a “very” good day. It’s full length bedded for the above reasons...it’s never let me down since spring of 1990. If there is a miss or a poor shot....it’s the shooter not the rifle! memtb


You should not use a rifle that will kill an animal when everything goes right; you should use one that will do the job when everything goes wrong." -Bob Hagel
 
Posts: 245 | Location: Winchester,Wyoming USA | Registered: 11 January 2005Reply With Quote
One of Us
Picture of Snellstrom
posted Hide Post
In my opinion start by free floating and shoot it see what you think.
If that's not what it likes then give it some fore end contact.
I like doing it in that order because it's harder to do in reverse.
What works for one rifle is not a cure all for all rifles.
 
Posts: 5604 | Location: Eastern plains of Colorado | Registered: 31 October 2005Reply With Quote
One of Us
posted Hide Post
If the barrel is a good barrel and the action properly bedded then free floating will win the day. For actions like Rem 700 and the M70 the barrel should be fully free floated and because of the position of the front action screw being in the centre of the bedding platform. Actions like Howa/Vanguard and others where the front action screw is right at the front of the action then about half inch to inch of barrel just in front of the action.

If the barrel is not real good and action bedding not real good then free floating will often be not so good and also might be very fussy with loads.
 
Posts: 7046 | Location: Sydney Australia | Registered: 14 September 2015Reply With Quote
One of Us
posted Hide Post
Most of my rifles are free floated and shoot very well. I have one that is full length bedded without upward pressure. It to shoots very well and has traveled across the country many times and held zero.

Start free floated and adjust as needed from there.
 
Posts: 130 | Location: Ozarks | Registered: 04 August 2017Reply With Quote
one of us
posted Hide Post
It largely depends on the individual barrel, and to a lesser extent on the design of the action and how solidly it can be bedded to the stock.

Slender barrels for light weight sporters tend to do much better when properly bedded, typically with some up-pressure near the end of the forearm.

Heavier barrels do fine either way if the action bedding is properly done, but floating can make up for imperfect bedding otherwise.

Although it is currently fashionable to believe that floated barrels offer better accuracy historical data doesn't always agree. For example, Winchester went to a floated barrel in their "new" Model 70 in 1964, but that rifle was never as accurate on average as the competing Remington Model 700 which was bedded with up pressure.
 
Posts: 13266 | Location: Henly, TX, USA | Registered: 04 April 2001Reply With Quote
one of us
posted Hide Post
I have never specified to my gunsmiths how to bed custom rifles meant for long range accuracy, but they all come back floated.

I did have a Rem700 ADL I full length bedded in a Brown Prec stock and it shot pretty well.


Don't Ever Book a Hunt with Jeff Blair
http://forums.accuratereloadin...821061151#2821061151

 
Posts: 7581 | Location: Arizona and off grid in CO | Registered: 28 July 2004Reply With Quote
One of Us
posted Hide Post
I start with free floating...quicker and easier to do...if NOGO then I do a pad at the front of the forend with ~6-8 lbs pressure. One or the other will usually do the trick...if not full bed and hope.

Tin #1-3 contour barrels seem to do better with a pad and a stiff wood stock...heavier barrels do better by floating...but the ONLY way to know is to start somewhere and keep trying if that doesn't work...barrels and stocks are like people...some good, some not so good.

Good Hunting tu2 beer
 
Posts: 1211 | Registered: 25 January 2014Reply With Quote
one of us
posted Hide Post
I start with bedding a gun TIGHT ALL THE WAY, test it, if not, then I go to THREE POINT BED, TEST IT, IF NOT I WILL THEN FREE FLOAT IT..

Why do I do this you ask? Simply because a rifle is an enity unto itself an may only shoot well with one of the three methods listed above and by using my method I can take wood out but I cannot put wood back in and if you start with free float and it doesn't shoot yer screwed! shocker

There are a lot of folks out there that just contend all guns shoot best free floated, that's BS but its easier to free float one and let the customer worry about getting it to shoot, at which point if its not shooting up to snuff ya have to fill it with glass!


Ray Atkinson
Atkinson Hunting Adventures
10 Ward Lane,
Filer, Idaho, 83328
208-731-4120

rayatkinsonhunting@gmail.com
 
Posts: 42226 | Location: Twin Falls, Idaho | Registered: 04 June 2000Reply With Quote
One of Us
posted Hide Post
What nature's forgotten we fix with AcraGlas
 
Posts: 66 | Location: Port Crane, NY | Registered: 11 February 2018Reply With Quote
One of Us
posted Hide Post
All of my timber stocked rifles are pillar bedded FIRST. Then I will float shooting groups before and after. If it groups well floated, then I bed the whole action and leave a 1”-2” pad under the knox form of the barrel chamber.
Varmint/target rifles have the pad negated and are floated from the recoil lug forward.

Cheers.
Wink
 
Posts: 684 | Location: N E Victoria, Australia. | Registered: 26 February 2009Reply With Quote
one of us
posted Hide Post
99 percent of my bolt action rifles are free floated.
 
Posts: 19736 | Location: wis | Registered: 21 April 2001Reply With Quote
One of Us
posted Hide Post
For wood stocked hunting rifles I prefer to float being more concerned with the point of impact not changing during the hunting season. Our deer season runs from November to early February so that's a lot of opportunity for the wood to move a little. I once read that a good barrel will shoot as well or better floated while a not so good barrel will shoot better with some forend pressure and that is why the manufactures put the pressure points at the front of the stock. But as we all know you can read anything!
 
Posts: 206 | Location: North Alabama | Registered: 13 January 2006Reply With Quote
One of Us
posted Hide Post
As posted, it's hard to put wood back but if you've got a rifle with the factory pressure point near the front of the stock, you can make some washers using biz cards and put them between the stock and the action. In effect, you are free floating the barrel (do the dollar bill trick) I assume that after a clean up, you have shot then rifle for accuracy as it came from the factory. If the factory set up nor the free float doesn't give you what you want, try putting a biz card between the pressure point and the barrel and see how that does.


Aim for the exit hole
 
Posts: 4348 | Location: middle tenn | Registered: 09 December 2009Reply With Quote
one of us
posted Hide Post
Wasbeeman,
That is correct, and its a good way to determine how your gun chooses to shoot and how it needs to be bedded.

As to wood moving,that's and old wives tail, based on cheap factory wood that never cured properly nor was laid out properly to start with, along with some other problems like poor inletting,those big gaps in the barrel channel do serve as a water storage in case you get thirsty..

Properly cured wood, laid out properly, and finished properly with some care each evening is as stable as fiberglass, and I have guns that have hunted all manor of weather and hardships without movement for over 45 years..Idaho is a testing ground for wet weather hunting of elk..I have an old pre 64 30-06 that the checkering is all but gone, worn off, looks like drift wood on a rifle that one might thing was never blued or the metal might be mistaken as stainless steel, This old gun has never been anything but a factory job and the wood never has moved nor has the POI changed since Ive owned it..Got lucky on that one, and it will never change now, its cured...

As to plastic stocks being indestructible, I saw one melt from being put behind the tent stove, another moved from heat in the trunk of a car, another from being left over lunch on the top of a pickup hood in extreme heat, They are vunerable, they are made by man, and yes Ive seen SS rust from neglect..

I only use rust blue and good European or some old world Walnut, not California cork wood on custom guns..I keep an eye on my factory Ruger African in .338, and my factory wood guns at least for several years as if they are going to move it doesn't take long to let you know, or so it seems to me.

No contradiction here just another point of view.


Ray Atkinson
Atkinson Hunting Adventures
10 Ward Lane,
Filer, Idaho, 83328
208-731-4120

rayatkinsonhunting@gmail.com
 
Posts: 42226 | Location: Twin Falls, Idaho | Registered: 04 June 2000Reply With Quote
One of Us
Picture of sambarman338
posted Hide Post
quote:
Originally posted by Atkinson:

... No contradiction here just another point of view.


And very well stated, too.

Ray, experience like that is more reason you should write a book. It could include observations and even chapters on equipment advice.
 
Posts: 5166 | Location: Melbourne, Australia | Registered: 31 March 2009Reply With Quote
one of us
posted Hide Post
Old wives tales my arse !
It because old wives had no way of knowing what their guns were doing !

The whole gun and its parts individually move and they move independently and in synergy with each other in a 3 dimensional frame.

The total motion construct can be broken down into modes and ultra high speed photography techniques have been employed to demonstrate the multiple modes in real time. There are multiple modes, as many as 8 moments have been described. There are apparently more.

The most commonly mode of interest is that what is referred to as barrel "twirlings" which are a assymetric figure 8 like pattern described by the muzzle position relative to the line of aim at the time of the initiation of the internal ballistics cycle. ie for each shot the muzzle points in a direction that falls in a described area that is different from the line of barrel position when the primer was struck. The value of this deviation from line of aim is stochastic within a upper and lower value limit.

by bedding or free floating the gunmaker can influence the magnitude of this randomness.


Other modes can be a up and down wave form bending of the barrel, elongation and shortening of the barrel, Even the scope and actions shows bending moments. Shooting from rests influence these moments.
 
Posts: 7857 | Registered: 16 August 2000Reply With Quote
One of Us
posted Hide Post
Another dissenting opionion! I had a Model 88 Winchester (while living in Louisiana many years ago), which would from summer to wet winter hunting, warp,shift,draw, or whatever you choose to call it....easily 1/8”. This huge amount of “warpage” was easily seen as I continued to open the barrel channel to eliminate the contact. When finished....you could have “dropped” a heavy, varmint weight barrel in the channel (open ditch)!
No doubt, a better wood, properly dried wood would have “probably” helped or eliminated the issue. But, once synthetics came upon the scene...they’re my “only” option.

I honestly love a beautiful wood stocked firearm....to look at! I take my hunting (as little as I do) pretty serious...the “pretty” stuff will stay home. The synthetic “stuff” goes hunting! memtb


You should not use a rifle that will kill an animal when everything goes right; you should use one that will do the job when everything goes wrong." -Bob Hagel
 
Posts: 245 | Location: Winchester,Wyoming USA | Registered: 11 January 2005Reply With Quote
One of Us
posted Hide Post
quote:
Originally posted by p dog shooter:
99 percent of my bolt action rifles are free floated.


100% of mine are free floated. That has proven to be the most accurate for me. I have about 20 of them.


NRA Patron member
 
Posts: 2653 | Location: Minnesota | Registered: 08 December 2006Reply With Quote
one of us
posted Hide Post
I had a 6mm-284 that would not shoot free-floated, but shot half-inch groups with a little forend pressure. Rifles differ.


TomP

Our country, right or wrong. When right, to be kept right, when wrong to be put right.

Carl Schurz (1829 - 1906)
 
Posts: 14744 | Location: Moreno Valley CA USA | Registered: 20 November 2000Reply With Quote
One of Us
Picture of Michael Robinson
posted Hide Post
I'm no expert, but I've had rifles that were full-bedded, free floated, and bedded with pressure at the tip of the fore end.

All types have shot well, but some didn't.

All of those that didn't were originally non-free floated rifles.

To fix those (to the extent that changing the bedding fixed anything), I free floated them.

I stopped trying to figure out why this happens!


Mike

Wilderness is my cathedral, and hunting is my prayer.
 
Posts: 13757 | Location: New England | Registered: 06 June 2003Reply With Quote
one of us
posted Hide Post
Alf,
Congratulations you have once again baffaled me with bull shit!! I see your off your meds! rotflmo


Ray Atkinson
Atkinson Hunting Adventures
10 Ward Lane,
Filer, Idaho, 83328
208-731-4120

rayatkinsonhunting@gmail.com
 
Posts: 42226 | Location: Twin Falls, Idaho | Registered: 04 June 2000Reply With Quote
One of Us
Picture of vapodog
posted Hide Post
quote:
Originally posted by Lamar:
yes..
they both work.


Fully agree....however I will make my first attempt a free floated barrel.

I put three wraps of electrical tape on the barrel and then glass bed full length. When the barreled action is removed the next day from the acraglass, there should be (at least theoretically) a gap between the barrel (tape removed) and the for end of the stock about .018 inches. That said I still at times am forced to take some 80 grit paper and a rounded block of wood and sand out more accraglass.

Years ago Remington intentionally put a "Bump" at the tip of the for end to keep some upward pressure on the barrel.....and many Remingtons shot very well.....That said, I have sanded that bump out and improved accuracy on occasion.

We go with what works.....but free floating is my first choice.


///////////////////////////////////////////////////////////////////////////
"Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery."
Winston Churchill
 
Posts: 28849 | Location: western Nebraska | Registered: 27 May 2003Reply With Quote
One of Us
posted Hide Post
No tip up pressure.
 
Posts: 1274 | Location: Saskatchewan, Canada.  | Registered: 22 August 2006Reply With Quote
one of us
posted Hide Post
three point bedding sometimes works well on feather weight barrels that are waspy by nature.

I have no problem with free float, only with those that are so closed minded that they think its the only way...Most folks that free float leave a gap large enough to bed a cockroach in..Most can't nor have ever inletted a wood stock..For those that freefloat, I suggest you have contact with knife edges at barrel line and only free floated enough to blow smoke thru underneath, saves rusted out barrels and dampness under the barrel. With any gun Im going to listen to the gun, not the homeboy on the internet when it comes to inletting, the gun will tell me how its going to shoot everytime.. sofa


Ray Atkinson
Atkinson Hunting Adventures
10 Ward Lane,
Filer, Idaho, 83328
208-731-4120

rayatkinsonhunting@gmail.com
 
Posts: 42226 | Location: Twin Falls, Idaho | Registered: 04 June 2000Reply With Quote
One of Us
posted Hide Post
quote:
Originally posted by Atkinson:
three point bedding sometimes works well on feather weight barrels that are waspy by nature.

I have no problem with free float, only with those that are so closed minded that they think its the only way...Most folks that free float leave a gap large enough to bed a cockroach in..Most can't nor have ever inletted a wood stock..For those that freefloat, I suggest you have contact with knife edges at barrel line and only free floated enough to blow smoke thru underneath, saves rusted out barrels and dampness under the barrel. With any gun Im going to listen to the gun, not the homeboy on the internet when it comes to inletting, the gun will tell me how its going to shoot everytime.. sofa


Can't make it much plainer than that


Aim for the exit hole
 
Posts: 4348 | Location: middle tenn | Registered: 09 December 2009Reply With Quote
one of us
posted Hide Post
quote:
Years ago Remington intentionally put a "Bump" at the tip of the for end to keep some upward pressure on the barrel.....and many Remingtons shot very well.....That said, I have sanded that bump out and improved accuracy on occasion.


I brought a 700 that had so much pressure on the for end that one could see the barrel move up when you tighten the action screws.

Wouldn't keep 5 rounds on a 8x11 after free floating it shot into 2 inches after bedding the action and first 3 inches in front of the action 3/4 of and inch.
 
Posts: 19736 | Location: wis | Registered: 21 April 2001Reply With Quote
One of Us
Picture of Fury01
posted Hide Post
Ray
Alf was explaining why you are right.
Happy shooting!


"The liberty enjoyed by the people of these states of worshiping Almighty God agreeably to their conscience, is not only among the choicest of their blessings, but also of their rights."
~George Washington - 1789
 
Posts: 2135 | Location: Where God breathes life into the Amber Waves of Grain and owns the cattle on a thousand hills. | Registered: 20 August 2002Reply With Quote
one of us
posted Hide Post
I never can figure that out!! He is a tricky bugger! jumping Alf is well versed and his savy of the English language is fantastic, as is his knowledge of guns and hunting, but sometimes this old Texas cowboy just isn't smart enough figure out what he is trying to say, I mean he uses his wifes perfume to lubricate his cases when he reloads, and stuff like that.. hilbily


Ray Atkinson
Atkinson Hunting Adventures
10 Ward Lane,
Filer, Idaho, 83328
208-731-4120

rayatkinsonhunting@gmail.com
 
Posts: 42226 | Location: Twin Falls, Idaho | Registered: 04 June 2000Reply With Quote
One of Us
Picture of Fury01
posted Hide Post
Well Ray I tell my wife and s few others, "there are a few advantages to being a Cowboy Gunfighter but darned few and fewer every day." But I tell myself that if the demand for cowboy gun fighters comes back; I'll have the market cornered.


"The liberty enjoyed by the people of these states of worshiping Almighty God agreeably to their conscience, is not only among the choicest of their blessings, but also of their rights."
~George Washington - 1789
 
Posts: 2135 | Location: Where God breathes life into the Amber Waves of Grain and owns the cattle on a thousand hills. | Registered: 20 August 2002Reply With Quote
one of us
posted Hide Post
Cowboy up and get after'em...


Ray Atkinson
Atkinson Hunting Adventures
10 Ward Lane,
Filer, Idaho, 83328
208-731-4120

rayatkinsonhunting@gmail.com
 
Posts: 42226 | Location: Twin Falls, Idaho | Registered: 04 June 2000Reply With Quote
  Powered by Social Strata  
 

Accuratereloading.com    The Accurate Reloading Forums    THE ACCURATE RELOADING.COM FORUMS  Hop To Forum Categories  Rifles  Hop To Forums  Medium Bore Rifles    Accuracy. Free floating or fully bedded barrel?

Copyright December 1997-2023 Accuratereloading.com


Visit our on-line store for AR Memorabilia