THE ACCURATERELOADING.COM MEDIUM BORE RIFLE FORUM

Page 1 2 

Moderators: Paul H
Go
New
Find
Notify
Tools
Reply
  
300 Win Mag with Boss
 Login/Join
 
Akshooter
One of Us
Picture of Akshooter
posted Hide Post
Josh - I'll send you a pm about the bear since were getting off topic with it

Hot Core
your right about getting back to answeing the question at hand. I think you covered it pritty well. I will ad my personal opinion about the boss system though.

I do belive the boss system dose work. I also belive that most of the vibration dampening will be taken care of with proper bedding of the reciver and barrel.

If your stock is not properly bedded you might find that adjusting the boss will have a significant positive affect on accuracy. If your metal is properly bedded you will still see a little benifit but not as much.


DRSS
NRA life
AK Master Guide 124
 
Posts: 1562 | Location: Alaska | Registered: 05 February 2006Reply With Quote
scottfromdallas
One of Us
Picture of scottfromdallas
posted Hide Post
I'm with Big Boar and Roll top. Honestly, people put way too much emphasis on minor velocity increases. Velocity increases give you range but little else on big game. Within 300 yards, there is virtually no difference in killing power between 30-06 and any 300 mag. Dead is dead. Over 300 yards the wind becomes a MAJOR factor and you have to question if the shot it ethical.

If you want more killing power, use a bigger bullet. A 338 mag with a 250 grain bullet is a much bigger jump in killing power than 30-06 vs 300 mag.

Josh, if you're good enough to shoot Cape Buffalo at 500 yards with your 300 win mag, more power to ya!



 
Posts: 1941 | Location: Texas | Registered: 19 July 2009Reply With Quote
Josh A.
One of Us
posted Hide Post
Scott, 500 yard cape buffalo point is silly. As to suitability for dangerous game, I used a 375 flanged double rifle on elephant and I haven't made up my mind what I will use when cape buffalo are on the list. Maybe a 450-400 or 470 double.

I did however use a 300 win mag single shot on an excellent eland.



josh
 
Posts: 304 | Location: West Texas | Registered: 01 April 2006Reply With Quote
Akshooter
One of Us
Picture of Akshooter
posted Hide Post
Eland are tough. I shot my first one with a .308 big mistake ran half way accross the ranch before we found it. The second I shot with a 9.3x74 double. Worked much better.


DRSS
NRA life
AK Master Guide 124
 
Posts: 1562 | Location: Alaska | Registered: 05 February 2006Reply With Quote
Moonshot
One of Us
Picture of Moonshot
posted Hide Post
quote:
Originally posted by Hot Core:
quote:
Originally posted by Moonshot:
Any suggestions for a starting point with this issue would be greatly appreciated. I can take the easy way out, but where would the fun in that be? M
Hey M, Just waded through the thread, but somehow missed where anyone answered your question.

First off, if you like the way it is shooting with some specific Factory Ammo, write the Setting down where you can not loose it. Then if you want to use that Factory Ammo again, you already have the correct Setting for it, or close to it.

I know of two ways that will work with the BOSS in Developing Loads. You can always start Low and work your way up until you get Pressure Indicators(CHE&PRE are the best). Then back off a few grains in a 300WinMag to give yourself long Case Life. And then load enough so you can "tune the BOSS" for that Load.

Or you can act as if there is no BOSS on it and use the never improved upon Creighton Audette Load Development Method to locate the best Harmonic without moving your Setting at all. Then fine tune by adjusting the Seating Depth.

Either way will work well without needing to use Politically Correct Bullets(PCBs).

Best of luck to you.


Thanks for the tip. Will be using Barnes, not for the political aspect but rather for the terminal performance.

The branching off topic is always a good read
 
Posts: 68 | Location: Beaverton, Oregon  | Registered: 20 August 2009Reply With Quote
  Powered by Social Strata Page 1 2  
 


Copyright December 1997-2023 Accuratereloading.com


Visit our on-line store for AR Memorabilia