THE ACCURATERELOADING.COM FORUMS


Moderators: Mark
Go
New
Find
Notify
Tools
Reply
  
9x57 Mauser
 Login/Join
 
One of Us
posted
Does anyone have a load for this cartridge with a 200gr bullet.All help will be greatly appreciated. Thanks Dave
 
Posts: 269 | Location: South East Florida | Registered: 01 August 2005Reply With Quote
one of us
Picture of asdf
posted Hide Post
This won't be much help, but it's all I have. A German site, www.ladedaten.info, once posted some purloined RWS data for European Rottweil powders using Hornady .358 bullets (I forgot to record which ones, but I think both were RN):

200 gn 3.03"
	R 901	42.5	2200
	R 903	50.0	2165

250 gn 3.11"
	R 902	43.0	2035
	R 903	47.0	2035


Starting loads were 2 gn less. These appear to be conservative data, perhaps due to using modern .358 bullets. Original hunting loads were, I believe, about 250 gn at near 2150 fps. I don't think RWS powder is available in the US. You might be able to find some near equivalents using a burn rate table, but that's risky business.
 
Posts: 980 | Location: U.S.A. | Registered: 01 June 2003Reply With Quote
One of Us
Picture of vapodog
posted Hide Post
here's one
200 Hornady (.358) IMR IMR-4320 46.0 2,150

I have a little more loading data but this is all with the 200 grain bullet.....this one is hard to find data for,.


///////////////////////////////////////////////////////////////////////////
"Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery."
Winston Churchill
 
Posts: 28849 | Location: western Nebraska | Registered: 27 May 2003Reply With Quote
One of Us
posted Hide Post
Thank you all for the info. Factory Kynoch were 245gr.I am using the 200gr 358 sierra rn because I think it is on the soft side and would cause less pressure in the slightly smaller 9mm bore Vapodog I am going to try the 4320 tomorrow I'll post what happens.
Thank Dave
 
Posts: 269 | Location: South East Florida | Registered: 01 August 2005Reply With Quote
one of us
posted Hide Post
Dave:

Just a thought. You might want to consider trying North Fork bullets in .358 caliber. With their driving band design, these might cause less pressure in the 9x57mm than conventional .358 caliber bullets.

They do, however, have a solid base but the driving bands may offset it. Might be worth a call to Mike at www.northforkbullets.com

RCG
 
Posts: 1132 | Location: Land of Lincoln | Registered: 15 June 2004Reply With Quote
Moderator
Picture of jeffeosso
posted Hide Post
THIS MAY NOT BE SAFE

i am a 358 win loader, so I have had quite a few loads for that...

when presented with a 9x57, I just used the SAME 358 win loads as starters, knowing I am going to give up ~200fps, but since the x57 case is larger, the pressure is lower


opinions vary band of bubbas and STC hunting Club

Information on Ammoguide about
the416AR, 458AR, 470AR, 500AR
What is an AR round? Case Drawings 416-458-470AR and 500AR.
476AR,
http://www.weaponsmith.com
 
Posts: 40229 | Location: Conroe, TX | Registered: 01 June 2002Reply With Quote
One of Us
posted Hide Post
Thanks guys I'll try both
Dave
 
Posts: 269 | Location: South East Florida | Registered: 01 August 2005Reply With Quote
one of us
Picture of asdf
posted Hide Post
I should have noted earlier, Hawk makes jacketed bullets of the correct diameter(s): .353, .354, and .356. The reputation of these bullets at high speed is poor, but shooters of slower speed rounds often report success, and the 250 RN in the 9x57 is not high speed. If you try them, you may want to mic your bullets received; one user (and so far only one user) here reported quality control can be spotty.

Lastly, QuickLoad suggests powders similar to Reloder 15 can produce 2150 fps for 250 gn bullets while staying within CIP pressure limits.
 
Posts: 980 | Location: U.S.A. | Registered: 01 June 2003Reply With Quote
  Powered by Social Strata  
 


Copyright December 1997-2023 Accuratereloading.com


Visit our on-line store for AR Memorabilia