THE ACCURATERELOADING.COM FORUMS


Moderators: Mark
Go
New
Find
Notify
Tools
Reply
  
IMR Enduron 4451 30-06?
 Login/Join
 
One of Us
posted
I'm interested in developing loads in the 30-06, with 175 grain LRX bullets.
Any of you distinguished gentlemen play with any loads similar?
Looking at IMRs site, they put the burn rate close to their 4350, albeit a tad slower.
It'll be burned in a 26" heavy barrel.

Thanks in advance
Bruce
 
Posts: 3785 | Location: B.C. Canada | Registered: 08 November 2005Reply With Quote
one of us
Picture of RMiller
posted Hide Post
With 175 Barnes LRX bullets I used Reloder -17 and IMR 4064.

Both do 2800 fps with that bullet out of my sons Mossberg ATR 30-06.


--------------------
THANOS WAS RIGHT!
 
Posts: 9823 | Location: Montana | Registered: 25 June 2001Reply With Quote
One of Us
Picture of Austin Hunter
posted Hide Post
same burn rate as H4350.

I did loads for my buddies Tikka T3 30-06 with a 22.43" barrel.

Lapau brass, CCI #200 primers, 180 gr Scirocco at 3.34"

53.5 gr RL 17 - 2,708 fps
56.0 gr H4350 - 2,680 fps

I used H4350 for my 404 J, so going with that, but bumping to 56.5 gr to hit 2,700 fps. both loads above <.75"

Same load should work for the Barnes. The bullet is a smidge longer, but the bands will reduce the pressure. Maybe start .5 to 1 gr below above if you are concerned.

The Scirocco has a higher BC and is 180 gr if it matters. I used TTSX in my 300 WBY, but think Scirocco and Accubonds are about perfect for the 30-06.


"Evil is powerless if the good are unafraid" -- Ronald Reagan

"Ignorance of The People gives strength to totalitarians."

Want to make just about anything work better? Keep the government as far away from it as possible, then step back and behold the wonderment and goodness.
 
Posts: 3080 | Location: Austin, Texas | Registered: 05 April 2006Reply With Quote
One of Us
posted Hide Post
Thank you good sir! Much appreciated!
quote:
Originally posted by Austin Hunter:
same burn rate as H4350.

I did loads for my buddies Tikka T3 30-06 with a 22.43" barrel.

Lapau brass, CCI #200 primers, 180 gr Scirocco at 3.34"

53.5 gr RL 17 - 2,708 fps
56.0 gr H4350 - 2,680 fps

I used H4350 for my 404 J, so going with that, but bumping to 56.5 gr to hit 2,700 fps. both loads above <.75"

Same load should work for the Barnes. The bullet is a smidge longer, but the bands will reduce the pressure. Maybe start .5 to 1 gr below above if you are concerned.

The Scirocco has a higher BC and is 180 gr if it matters. I used TTSX in my 300 WBY, but think Scirocco and Accubonds are about perfect for the 30-06.
 
Posts: 3785 | Location: B.C. Canada | Registered: 08 November 2005Reply With Quote
One of Us
Picture of Barstool(er)
posted Hide Post
I found a sweet load of IMR Enduron 4451 for mine and a friend's 30-06 shooting 175gr Sierra MKs to be 55.8gr.
With both rifles having 24" barrels we are getting ~2725 fps.
Loads used Rem 91/2 primers, Rem brass and bullets were seated 3.30

These loads were worked up a .2 grain intervals starting a 54gr.

The Enduron sure reduces the copper fouling as advertised.

My rifle (Ruger 77 Mk II) has a custom trigger and a Leupold 3x9 and keeps 5 shot groups well inside an inch. My friend's rifle is a custom barreled Mauser 98 with heavy barrel and a Leupold 4.5x14 which keeps 5 shot groups well inside a half inch.

Barstooler


Weapon of Choice: 30mm Gatling Gun

Over 1500 posts as "Barstooler"
 
Posts: 33 | Location: Colorado Springs | Registered: 09 June 2015Reply With Quote
One of Us
posted Hide Post
Barstooler, thank you!
 
Posts: 3785 | Location: B.C. Canada | Registered: 08 November 2005Reply With Quote
  Powered by Social Strata  
 


Copyright December 1997-2023 Accuratereloading.com


Visit our on-line store for AR Memorabilia