THE ACCURATERELOADING.COM SHOTSHELL RELOADING FORUM

Go
New
Find
Notify
Tools
Reply
  
Best way to clean shotgun hulls?
 Login/Join
 
One of Us
posted
What is the best way to clean alot of empty hulls collected at the range? I've been using a nylon 12ga brush to get the dirt out and the give it a wipe a damp cloth. This method works well when someone else does it!
 
Posts: 885 | Location: Eastern Cape, South Africa | Registered: 08 January 2010Reply With Quote
One of Us
posted Hide Post
Deprime, place in a mesh bag and run through a washing machine. Let air dry.


Yackman
 
Posts: 582 | Location: Searcy,AR | Registered: 23 February 2003Reply With Quote
One of Us
posted Hide Post
Thank you Jim. I have heard of this method before but I wasnt sure if it was true or not.
 
Posts: 885 | Location: Eastern Cape, South Africa | Registered: 08 January 2010Reply With Quote
One of Us
posted Hide Post
Works great as long as they are all plastic, the bag is stout (pillow cases fall apart), and your wife is understanding. The dryer can be a bit rough on the ears.
C.G.B.
 
Posts: 1103 | Registered: 25 January 2005Reply With Quote
new member
posted Hide Post
Why do you need to clean them? Just the general dirt from the ground or do they have another issue?
 
Posts: 14 | Location: Wisconsin | Registered: 02 September 2007Reply With Quote
One of Us
posted Hide Post
Charles, these hulls usually have anything from sand to grass, even found bugs in them! I have a guy collect once a month for me and usually I save about 40% of these as the rest are usually not good enough for reloading.
 
Posts: 885 | Location: Eastern Cape, South Africa | Registered: 08 January 2010Reply With Quote
One of Us
posted Hide Post
Dish washer works too
 
Posts: 1845 | Registered: 01 November 2009Reply With Quote
One of Us
Picture of icemanls2
posted Hide Post
Never cleaned a hull, Havn't found the need, but i guess if i had some real muddy ones i would. Now i know how to do it if the need arrises.
 
Posts: 442 | Location: Michigan | Registered: 14 October 2009Reply With Quote
one of us
posted Hide Post
Why get em wet?
Find an old tumbler dryer.
Get a old wool blanket, dump a bunch of hulls in the center just enuf so they are a bit loose in it (will tumble around inside).
Tie up the ends so the hulls won't fall out.
Throw the kiboodle into the dryer and let it run for an hour.
They will come out clean, and dry and the brass will prolly look a lot better too.

(I used to trap shoot a lot so I found an old dryer that had a dead heating element.)
This was the method I used then.
 
Posts: 434 | Location: Wetcoast | Registered: 31 October 2004Reply With Quote
one of us
posted Hide Post
quote:
Originally posted by JD Miller:
Dish washer works too


+1

I use the mesh bags, (4). 2 on the top rack, and 2 on the bottom. I usually put around a hundred in each bag, and use the "Pot Scrubber" cycle with the DRYING HEAT TURNED OFF. I usually run them through my MEC Case Conditioner first which deprimes and resizes them. By having the primer hole open water drains out easier, and the inside of the shells come out much cleaner. After they dry, (3 hours or so in the afternoon Sun), they're ready to reload, and come out looking factory new. I like nice, clean ammo. I have noticed that wads seat much easier and more consistently in clean cases. It simply makes for better, more dependable reloads. Bill T.
 
Posts: 1540 | Location: Glendale, Arizona | Registered: 27 December 2003Reply With Quote
  Powered by Social Strata  
 


Copyright December 1997-2023 Accuratereloading.com


Visit our on-line store for AR Memorabilia