THE ACCURATERELOADING.COM GUNSMITHING FORUM


Moderators: jeffeosso
Go
New
Find
Notify
Tools
Reply
  
M70 trigger adjustment
 Login/Join
 
One of Us
Picture of Rayderluvr
posted
Is adjust ing the trigger on a M70 pretty straightforward or should I take it to a gunsmith??


You can pick your friends, and you can pick your nose.....but you can't pick your friends nose!
 
Posts: 72 | Location: SW Misssouri | Registered: 02 February 2006Reply With Quote
one of us
Picture of ramrod340
posted Hide Post
See if this helps make up your mind.

Adjusting the Model 70 Trigger
by Frank Kleinburg (fkleinbu@tivoli.tivoli.com)
(Original article posted at www.recguns.com)
Let me discuss how the trigger on the Model 70 works. Knowing how it works will allow you to know how a gunsmith would
adjust it.

The trigger mechanism on the Winchester Model 70 is remarkably simple. Remove the barreled acton of a Model 70 from
it's stock and you can see just how simple it is. You will see a trigger that pivots on a pin. Look at the rear portion of the trigger
(normally hidden by the stock) and you will see a square head screw (the trigger stop screw), three nuts, and a spring (we'll call it
the trigger return spring).

The purpose of the trigger stop screw is to limit the amount of over travel of the trigger. It is possible to screw the trigger stop
screw in far enough that you will not be able to pull the trigger enough to release the sear. Ideally the trigger stop screw should
be screwed in as far as it can and still have enough trigger movement to reliably release the sear. This will allow for the greatest
amount of adjustment of the trigger spring tension.

Tension on the trigger return spring determines a majority of the trigger pull weight (the rest of the trigger pull weight comes
from the friction between the trigger and the sear). The spring surrounds the trigger stop screw, both can be seen just behind
the trigger. The trigger stop screw is held in place by a pair of captive nuts, one on each side of the part of the trigger the stop
screw passes through. A third nut sets the tension on the trigger spring. Tightening this third nut (turning it clockwise) against the
trigger spring will increase the trigger pull. And turning it counter clockwise will decrease the trigger pull weight.

After making any adjustments, be absolutely sure to test for an excessively light trigger. To do this, screw the barreled action
back in the stock. With the bolt cocked, in the closed position on an empty chamber, and the safety off, butt down the rifle. That
is hold the rifle barrel pointing upward, let the butt bounce on the ground. It should take a considerable bump to cause the firing pin
to drop (on the empty chamber).

On a friend's pre-64 Model 70 trigger, the spring had to be changed because enough of the trigger spring pretension could not
be removed to get an acceptable trigger pull weight. Yet on another (on one of those new classic actions), it was possible to
remove ALL of the trigger spring pretension. This is a dangerous situation because only the trigger to sear tension keeps the
cocked rifle from firing.

Well I hope you now have a better understanding of how a Model 70 trigger works. Of course for all trigger pull weight
adjustments you should take your rifle to a reputable gunsmith.


As usual just my $.02
Paul K
 
Posts: 12881 | Location: Mexico, MO | Registered: 02 April 2001Reply With Quote
One of Us
Picture of Masterifleman
posted Hide Post
If your the least bit mechanically inclined, adjusting the Winchester 70 trigger is easy. The only thing that needs real care in dooing is that most of the triggers have far more contact at the trigger/sear connection than needed and prevent a real fine adjustment. That little "pad" or "hook" where the trigger and sear engage should only be .006" high and perfectly square with a backslope so that the trigger doesn't drag when the sear disengages. Scare you off yet? Once you adjust the weight of pull, using the long screw with the spring and lock nuts, it's easy to adjust the overtravel to have a great crisp trigger. I never could understand people wanting to replace the Model 70 factory trigger with an aftermarket.


"I ask, sir, what is the Militia? It is the whole people. To disarm the people is the best and most effective way to enslave them" - George Mason, co-author of the Second Amendment during the Virginia convention to ratify the Constitution
 
Posts: 1699 | Location: San Antonio, TX | Registered: 14 April 2004Reply With Quote
One of Us
Picture of Rayderluvr
posted Hide Post
Thanks for your help. I live near a Winchester Certified Gunsmith (he is listed in the literature I received with my new rifles), I may be best off to have him adjust my triggers.
Thanks!


You can pick your friends, and you can pick your nose.....but you can't pick your friends nose!
 
Posts: 72 | Location: SW Misssouri | Registered: 02 February 2006Reply With Quote
  Powered by Social Strata  
 


Copyright December 1997-2023 Accuratereloading.com


Visit our on-line store for AR Memorabilia