THE ACCURATERELOADING.COM GUNSMITHING FORUM

Accuratereloading.com    The Accurate Reloading Forums    THE ACCURATE RELOADING.COM FORUMS  Hop To Forum Categories  Guns, Politics, Gunsmithing & Reloading  Hop To Forums  Gunsmithing    Retaining Zero and Removing BBL Action from Stock

Moderators: jeffeosso
Go
New
Find
Notify
Tools
Reply
  
Retaining Zero and Removing BBL Action from Stock
 Login/Join
 
One of Us
Picture of Mike_Dettorre
posted
Is ther anything that can be done...little tweeks...like steel bedding...steel wasxhers under screws...toraue wrench in your pocket that would allow you to assemble and disassemble the rifle that would require then a minimal amount of re-zeroing


Mike

Legistine actu quod scripsi?

Never under estimate the internet community's ability to reply to your post with their personal rant about their tangentially related, single occurrence issue.




What I have learned on AR, since 2001:
1. The proper answer to: Where is the best place in town to get a steak dinner? is…You should go to Mel's Diner and get the fried chicken.
2. Big game animals can tell the difference between .015 of an inch in diameter, 15 grains of bullet weight, and 150 fps.
3. There is a difference in the performance of two identical projectiles launched at the same velocity if they came from different cartridges.
4. While a double rifle is the perfect DGR, every 375HH bolt gun needs to be modified to carry at least 5 down.
5. While a floor plate and detachable box magazine both use a mechanical latch, only the floor plate latch is reliable. Disregard the fact that every modern military rifle uses a detachable box magazine.
6. The Remington 700 is unreliable regardless of the fact it is the basis of the USMC M40 sniper rifle for 40+ years with no changes to the receiver or extractor and is the choice of more military and law enforcement sniper units than any other rifle.
7. PF actions are not suitable for a DGR and it is irrelevant that the M1, M14, M16, & AK47 which were designed for hunting men that can shoot back are all PF actions.
8. 95 deg F in Africa is different than 95 deg F in TX or CA and that is why you must worry about ammunition temperature in Africa (even though most safaris take place in winter) but not in TX or in CA.
9. The size of a ding in a gun's finish doesn't matter, what matters is whether it’s a safe ding or not.
10. 1 in a row is a trend, 2 in a row is statistically significant, and 3 in a row is an irrefutable fact.
11. Never buy a WSM or RCM cartridge for a safari rifle or your go to rifle in the USA because if they lose your ammo you can't find replacement ammo but don't worry 280 Rem, 338-06, 35 Whelen, and all Weatherby cartridges abound in Africa and back country stores.
12. A well hit animal can run 75 yds. in the open and suddenly drop with no initial blood trail, but the one I shot from 200 yds. away that ran 10 yds. and disappeared into a thicket and was not found was lost because the bullet penciled thru. I am 100% certain of this even though I have no physical evidence.
13. A 300 Win Mag is a 500 yard elk cartridge but a 308 Win is not a 300 yard elk cartridge even though the same bullet is travelling at the same velocity at those respective distances.
 
Posts: 10181 | Location: Loving retirement in Boise, ID | Registered: 16 December 2003Reply With Quote
one of us
posted Hide Post
If you don't know how to do it yourself then get a qualified person to glass bed it for you. You can take apart a dozen times and still be on Zero.
 
Posts: 1159 | Location: Florida | Registered: 16 December 2004Reply With Quote
one of us
posted Hide Post
I used to do the 'poor-mans takedown' when travelling to and from exploration camps and in and out of planes and helicopters. all I did was just pull and re-assemble the bbl'd action, and wrapped it and the stock with clothes and stuffing it in a hockey bag with the rest of my gear.

I stamped match-marks in the bottom metal, but found it was really unneccesary since with a good bedding job, the screws will just stop turning when tight. I also used a fully free-floating bedding job and never had a problem retaining zero.
 
Posts: 344 | Registered: 28 May 2004Reply With Quote
One of Us
posted Hide Post
I have two Model 700 Remingtons, one in 7mm Rem. Mag. and the other in 338 Win. Mag. One is in a customized standard Remington stock and the other wears a Brown Precision. When I go on a distant hunt it seems I always want the Brown Precision on what I am going to carry, the 7mm or the 338. Because of that I have swapped the stock back and forth quite a few times. Each time, the rifles stay in zero. Never have had a problem with bullet dispersion. Maybe I am just lucky cause I for sure check them each time at the range, or maybe it is just these rifles, but I sure am thankful it has worked for me.
 
Posts: 1332 | Location: Western NC | Registered: 08 January 2005Reply With Quote
one of us
posted Hide Post
If it has a Termite Food stock, trash it.

If it has a Synthetic Stock, have it Pillar Bedded and put tiny Witness marks on the Screws so you know you have re-tightened them to the exact same spot.
 
Posts: 9920 | Location: Carolinas, USA | Registered: 22 April 2001Reply With Quote
  Powered by Social Strata  
 

Accuratereloading.com    The Accurate Reloading Forums    THE ACCURATE RELOADING.COM FORUMS  Hop To Forum Categories  Guns, Politics, Gunsmithing & Reloading  Hop To Forums  Gunsmithing    Retaining Zero and Removing BBL Action from Stock

Copyright December 1997-2023 Accuratereloading.com


Visit our on-line store for AR Memorabilia