THE ACCURATERELOADING.COM GUNSMITHING FORUM

Page 1 2 

Moderators: jeffeosso
Go
New
Find
Notify
Tools
Reply
  
Rate the Mauser actions
 Login/Join
 
cal30 1906
One of Us
Picture of cal30 1906
posted Hide Post
sbhva


do you have the resources to look up a
serial 3 for a 1909 argentine mauser?




If it cant be Grown it has to be Mined! Devoted member of Newmont mining company Underground Mine rescue team. Carlin East,Deep Star ,Leeville,Deep Post ,Chukar and now Exodus Where next? Pete Bajo to train newbies on long hole stoping and proper blasting techniques.
Back to Exodus mine again learning teaching and operating autonomous loaders in the underground. Bringing everyday life to most individuals 8' at a time!
 
Posts: 3090 | Location: Northern Nevada & Northern Idaho | Registered: 09 April 2005Reply With Quote
sbhva
one of us
Picture of sbhva
posted Hide Post
quote:
Originally posted by cal30 1906:
sbhva


do you have the resources to look up a
serial 3 for a 1909 argentine mauser?


No, only for Husqvarna commercial firearms.


Steve
 
Posts: 120 | Location: Wisconsin, USA | Registered: 05 February 2004Reply With Quote
cal30 1906
One of Us
Picture of cal30 1906
posted Hide Post
quote:
No, only for Husqvarna commercial firearms.

Steve



Any ideas? if not someone here is sure to
help out.




If it cant be Grown it has to be Mined! Devoted member of Newmont mining company Underground Mine rescue team. Carlin East,Deep Star ,Leeville,Deep Post ,Chukar and now Exodus Where next? Pete Bajo to train newbies on long hole stoping and proper blasting techniques.
Back to Exodus mine again learning teaching and operating autonomous loaders in the underground. Bringing everyday life to most individuals 8' at a time!
 
Posts: 3090 | Location: Northern Nevada & Northern Idaho | Registered: 09 April 2005Reply With Quote
Roland1
one of us
posted Hide Post
quote:
Originally posted by lb404:
Ray, whom would you suggest to work over a half dozen Mauser actions? I don't need a Hartman and Weiss quality. I like Tom Burgess work, I just don't think I will live long enough to see them all done by him. Is Jack Belk still working?

lb404,
I’m sure if Tom Burgess tailors your Mauser actions, the will be as good or maybe superior than a Hartman & Weiss.
Lon Paul does a good job as well.

Success,
Roland
 
Posts: 654 | Registered: 27 June 2004Reply With Quote
Paul B
one of us
posted Hide Post
quote:
Originally posted by sbhva:
quote:

The number is 1177XX, but it is on the barrel and not the action.
Paul B.


The barreled action was made in 1951. Most likely it was originally a US model '51 Hi-Power, but impossible to know without the original stock. The serial number on the barrel instead of the action is correct for a Husqvarna rifle.


Thanks a lot. that helps a bunch. Now, if I can chase down an original stock somewhere, I'll be in hawg heaven. Right now, I have it sitting in a J.C. Higgin Model 50 stock. I think I'd like to restore it to like new if I can. Again, thanks for the date.
Paul B.
 
Posts: 2814 | Location: Tucson AZ USA | Registered: 11 May 2001Reply With Quote
Atkinson
one of us
posted Hide Post
I think they should all be surface ground especially if you are going to use QD rings, that will insure return to zero...

Surface grinding gets everyhthing square to the world, and thats the best start to a proper custom rifle...A bunch of factory guns could use this treatment as opposed to shims that create stresses in the base, rings and scope.....


Ray Atkinson
Atkinson Hunting Adventures
10 Ward Lane,
Filer, Idaho, 83328
208-731-4120

rayatkinsonhunting@gmail.com
 
Posts: 42320 | Location: Twin Falls, Idaho | Registered: 04 June 2000Reply With Quote
  Powered by Social Strata Page 1 2  
 


Copyright December 1997-2023 Accuratereloading.com


Visit our on-line store for AR Memorabilia