THE ACCURATERELOADING.COM GUNSMITHING FORUM


Moderators: jeffeosso
Go
New
Find
Notify
Tools
Reply
  
Sticky extraction
 Login/Join
 
One of Us
posted
Having an issue with a Ruger Hawkeye 338WM. With factory ammo it's very difficult to extract a fired case from the chamber. Reloaded rounds are no problem. It's happening with three different brands of ammo. Could this be a chamber issue needing a reamer and polishing?
 
Posts: 309 | Location: WV | Registered: 14 February 2005Reply With Quote
One of Us
Picture of Westpac
posted Hide Post
Where it's happening with factory stuff and not reloaded stuff tells me it might be ammo related. The chamber cannot differentiate between hand loaded brass and factory new brass. Is there a difference in how the bolt feels when opened between the factory stuff and the handloads? Measure and compare dimensions between the factory stuff and your handloads.


_______________________________________________________________________________
This is my rifle, there are many like it but this one is mine. My rifle is my best friend, it is my life.
 
Posts: 3171 | Location: SLC, Utah | Registered: 23 February 2007Reply With Quote
One of Us
Picture of dpcd
posted Hide Post
Polishing maybe but if it really does need a reamer, it needs to go back to Ruger. Is it hard to chamber a round? Is the chamber rough; can you see any rings in it? If rounds go in easily, you do not need to enlarge the chamber. It might be rough. Need more info.
 
Posts: 17404 | Location: USA | Registered: 02 August 2009Reply With Quote
One of Us
posted Hide Post
Chambering and bolt lift are fine. It's the extraction that's tight. Three different factory loads are hanging up. Unfired rounds chamber and extract smoothly. Thinking polishing might be in order.
 
Posts: 309 | Location: WV | Registered: 14 February 2005Reply With Quote
One of Us
Picture of dpcd
posted Hide Post
In that case definitely do not use a reamer on your chamber; it is already to spec if it chambers and extracts live rounds. Look inside for a ring or roughness; best to remove the barrel for that, but you can use a drill and some 600 grit paper wrapped around a slotted dowel but go slowly and don't grind your rifling any.
 
Posts: 17404 | Location: USA | Registered: 02 August 2009Reply With Quote
One of Us
posted Hide Post
I had a 7mmSTW in a Winchester CRF model 70 that would have extremely hard to extract issues with factory Rem ammo. The first round fired would have very hard bolt lift, the second round I would have to beat the bolt open with the butt of my hand and the third round I would have to use my foot to extract the case. I had the dealer I bought it from try to smooth the chamber walls with a Fordum (sp) and steel wool and it might have helped a little but it was so little it was almost indistinguishable. I didn't reload then (started immediately after trading this rifle), but think the ammo was loaded too hot for my chamber. That seems to me like the same trouble you are experiencing.


Dennis
Life member NRA
 
Posts: 1191 | Location: Ft. Morgan, CO | Registered: 15 April 2005Reply With Quote
One of Us
Picture of Oddbod
posted Hide Post
If the rifle is covered by Ruger's warranty, send it back.
If it isn't, email them with the problem & if they say send it back, then do just that.
 
Posts: 610 | Location: Cumbria, UK | Registered: 09 July 2007Reply With Quote
One of Us
posted Hide Post
We are under a time crunch for a July departure to SA. We have located a shop with a bore scope and will do an inspection this weekend. Hopefully it is a n easy fix. I doubt the gun is still under warranty due to having it glass bedded and refinished.
 
Posts: 309 | Location: WV | Registered: 14 February 2005Reply With Quote
  Powered by Social Strata  
 


Copyright December 1997-2023 Accuratereloading.com


Visit our on-line store for AR Memorabilia