The Accurate Reloading Forums
custom bases for talley rings
custom bases for talley rings
Looking for a good smith to make/install custom bases on several of my custom rifles. The last three I have used no longer are doing them or are unreliable. Any suggestions
/
square shooter
06 July 2010, 01:46
jsl3170michael scherz does them but reports vary on his reliability.
06 July 2010, 03:03
M1TankerI have one set from Michael Scherz and 2 more that should be delivered any day. I am very impressed with his bases.
Dean Zollinger also does an amazing job with his bases.
William Berger
True courage is being scared to death but saddling up anyway. - John Wayne
The courageous may not live forever, but the timid do not live at all.
any examples of their work?? I was really happy with the two I had working with me. Both have since retired.
square shooter
06 July 2010, 21:31
CAS IISteve Yamagishi did some nice work for me on a few sets of custom bases. Here is a not great photo of one of the sets:
06 July 2010, 23:44
30 Caliber Mag FanTry "toomanytools" here on the board, a/k/a John Farner.
He did some great bases for use with Tally rings for a VZ-24 for me.
May the wind be in your face and the sun at your back.
P. Mark Stark
07 July 2010, 01:26
M1TankerI dont have any photos of my Scherz bases but I pasted a link to his site below.
http://www.michaelscherz.com/scope_bases.htmlHere is a pic of my Zollinger bases.
William Berger
True courage is being scared to death but saddling up anyway. - John Wayne
The courageous may not live forever, but the timid do not live at all.
07 July 2010, 05:07
lee440I'm happy for the folks here that had good luck with Mr. Scherz, he does good work.... when he works. Based on my and several other members experience with him, I will never trust any work with him again. Caveat Emptor!!!
DRSS(We Band of Bubba's Div.)
N.R.A (Life)
T.S.R.A (Life)
D.S.C.
thanks all. Still need help finding someone that can do 10-20 sets a year and not need to beat on to do the work.
square shooter
07 July 2010, 07:10
kcstott10 to 20 sets a year. Sounds like a small run production job. Different action or all the same?
I'd be more then happy to quote it.
www.KLStottlemyer.comDeport the Homeless and Give the Illegals citizenship. AT LEAST THE ILLEGALS WILL WORK
07 July 2010, 07:15
M1Tankerquote:
Originally posted by lb404:
thanks all. Still need help finding someone that can do 10-20 sets a year and not need to beat on to do the work.
I would be willing to bet that both the names I mentioned can handle that for you without issue. You should give them a call before writing them off. I have extensive dealings with both and had nothing but excellent service.
William Berger
True courage is being scared to death but saddling up anyway. - John Wayne
The courageous may not live forever, but the timid do not live at all.
kcstott, there might be three different types of actions; large and small ring Mauser actions and,pre-64 model 70 actions.Occasionally i might need a Winchester Classic action done. I would love to start this project. I need names and numbers please!
square shooter
07 July 2010, 07:50
GeoffM24Jim Dubell of Delta Gunshop did these basis for me for my 404 project
Uploaded with
ImageShack.us07 July 2010, 08:42
Chuck1911I second John aka TOOMANYTOOLS
Chuck Warner
Pistolsmith
/
07 July 2010, 08:53
kcstottPM sent
www.KLStottlemyer.comDeport the Homeless and Give the Illegals citizenship. AT LEAST THE ILLEGALS WILL WORK
08 July 2010, 00:07
450/400Mark Stratton did a set or stradle bases for my Brno 21h with a cut out so that the iron sight could still be used.
Mark stratton did most of mine, and a great job.
After the last job he did, he told me he had to shut down and would not be working for a while. IS MARK working now???? does anyone have contact numbers?
square shooter
10 July 2010, 23:01
Duane WiebeI'd like to point out something in Steve Yamagishi's bases.
Notice how the dovetail does not extend beyond the the forward or rear recoil shoulder. Lots more work, but sure stands out as an ultra professional job.
By the way: He is now Steve BUTTON, recently moved and set up shop in Olympia, WA 360 918 8283