The Accurate Reloading Forums
military Mauser rear sight scope base

This topic can be found at:
https://forums.accuratereloading.com/eve/forums/a/tpc/f/9411043/m/552104163

03 November 2005, 22:34
Scota4570
military Mauser rear sight scope base
Anyone done one? I will not pay $50 for something I can make better in a half hour on the mill.

The rifle is a Turk. My plan right now is to remove the sight and replace it with a block that fits the same. The block will then receive a Weaver generic sight base rail. The red dot sight goes on that. The barrel gets repaced with a 16" 45ACP one, but that is irrelevent. Do you have anything to pass along from your experience with such work? Any on line pictures?
03 November 2005, 22:44
Rick 0311
Do a search on here because this topic was discussed within the last month or so.
04 November 2005, 03:49
D Humbarger
45 ACP! Just go ahead & do it in 50 Beauwolf. thumb



Doug Humbarger
NRA Life member
Tonkin Gulf Yacht Club 72'73.
Yankee Station

Try to look unimportant. Your enemy might be low on ammo.
04 November 2005, 17:30
mb
If you're going to rebarrel anyway why not just bolt the Weaver base directly on the barrel? If you plan ahead you can even have the new barrel turned to a radius that fits an existing base (think Contender or Encore). Good hunting!
04 November 2005, 18:06
El Deguello
Yes, I did it once with an Argentine Mauser that was too nice to butcher up. Put a intermediate-eye relief scope on it. It worked, but was unsatisfactory in other ways (weight, balance, clumsiness, etc.)


"Bitte, trinks du nicht das Wasser. Dahin haben die Kuhen gesheissen."
04 November 2005, 19:55
bartsche
waveIf you send me your E-Mail Add. I'll send you some photos of mountings I've done on the Mauser rear sights to mount scopes. There is an alum. one on the market that I saw fail miserably. The ones I've designed are of steel. thumbroger


Old age is a high price to pay for maturity!!! Some never pay and some pay and never reap the reward. Wisdom comes with age! Sometimes age comes alone..
04 November 2005, 23:10
Scota4570
http://www.rhinelandarms.com/

This is what I am assembling. Click on the Mauser kit. It is for a co-worker. It is a bit crude. The price is low though. I guess you get what you pay for. It is about the most econimical way to make a 45ACP bolt gun.

I would much rather see a full length barrel. I would guess they are getting two barrels out of one blank. I also do not care for the Savage style barrel nut. Hey, it is a project to keep busy with and some goodies traded to me for my work.

The reason for using a sight base mount is that the new barrel is made to the same contour as the old. The sight base will slip on and solder in place. I hope to retain some of the military look.
05 November 2005, 07:56
bartsche
Roll EyesThis looks like a perfect application for the scout style scope. thumbroger


Old age is a high price to pay for maturity!!! Some never pay and some pay and never reap the reward. Wisdom comes with age! Sometimes age comes alone..
05 November 2005, 09:30
tnekkcc
Here is a 45acp Mauser I made in 1999 with a 1903 Turk, a Shilen .452" barrel blank, drilling a tapping for Weaver mounts #45 and #46, bending the bolt with an Oxyaccetalene set up. Shoots a 4" 20 shot group at 100m.

You can buy a bent bolt body on Ebay. There is a guy who does hundreds of them.