THE ACCURATERELOADING.COM GUNSMITHING FORUM


Moderators: jeffeosso
Go
New
Find
Notify
Tools
Reply
  
Custom hammer spring needed
 Login/Join
 
One of Us
posted
After my Ruger Redhawk Super Alaskan came back from the custom shop, it no longer reliably fires 454 Casull, even after replacing the "custom" one w. a stock replacement one from Wolff.

Does anyone know of a custom maker who can make a stronger one for me? Wolff will not, apparently.

Thank You,
Brad


And for the support of this Declaration, with a firm reliance on the protection of divine Providence, we mutually pledge to each other our Lives, our Fortunes and our sacred Honor.
 
Posts: 863 | Location: Texas | Registered: 25 January 2006Reply With Quote
One of Us
Picture of Rusty Marlin
posted Hide Post
Warning smart ass comment to follow:

How about the "Custom" shop that dicked it up in the first place?

Smart ass mode = OFF


While holding the hammer back at full cock, pull the trigger and check to be sure the the T-bar is fully covering the firing pin and that the there isn't a chamfer on the front side along the top edge that may also be reduceing contact area.
If you have the measuring tools you should also measure your firing pin protusion. You'll want .050" to .060"; to measure this you need to ease the hammer back enough to clear the T-bar, then pull the trigger to raise the T_bar under the hammer, lower the hammer against the T-bar so it pushes the firing pin out of the recoil sheild. As you will have the cylinder open you may need to pull the cylinder release lever out with your finger nail so the hammer can be retracted.


Rusty's Action Works
Montross VA.
Action work for Cowboy Shooters &
Manufacturer of Stylized Rigby rifle sights. http://i61.photobucket.com/alb.../th_isofrontleft.jpg
 
Posts: 863 | Location: Northern Neck Va | Registered: 14 December 2005Reply With Quote
One of Us
posted Hide Post
The custom shop says it's fine w. federal and winchester ammo (which, as far as I've tested it, it is... and that's their response... They had it for ~ year, and I'm not inclined to let them have it back -- aside from the spring, the work was excellent, however...)

I will check the firing pin protrusion -- it fires 45 oolt just fine -- does that eliminate the firing pin issue?


And for the support of this Declaration, with a firm reliance on the protection of divine Providence, we mutually pledge to each other our Lives, our Fortunes and our sacred Honor.
 
Posts: 863 | Location: Texas | Registered: 25 January 2006Reply With Quote
One of Us
Picture of Rusty Marlin
posted Hide Post
Sounds like they "over tuned" it. The .454 uses small rifle primers and as such requires a fair bit more impact than a standard large pistol primer as used in a .45Colt, the data on how much more is out in my shop and I'll look it up latter.

Measure the firng pin protusion and get a factory hammer spring. Light springs work fine for playing around, but the .454 needs the heavy hit of a factory spring.


Rusty's Action Works
Montross VA.
Action work for Cowboy Shooters &
Manufacturer of Stylized Rigby rifle sights. http://i61.photobucket.com/alb.../th_isofrontleft.jpg
 
Posts: 863 | Location: Northern Neck Va | Registered: 14 December 2005Reply With Quote
One of Us
posted Hide Post
I've already switched back to the original poundage spring, at least according to Wolff (14#s) I'm going to try and order one from Ruger as well, in case it's more powerful.


And for the support of this Declaration, with a firm reliance on the protection of divine Providence, we mutually pledge to each other our Lives, our Fortunes and our sacred Honor.
 
Posts: 863 | Location: Texas | Registered: 25 January 2006Reply With Quote
  Powered by Social Strata  
 


Copyright December 1997-2023 Accuratereloading.com


Visit our on-line store for AR Memorabilia