THE ACCURATERELOADING.COM GUNSMITHING FORUM


Moderators: jeffeosso
Go
New
Find
Notify
Tools
Reply
  
M70 sights
 Login/Join
 
one of us
posted
Good all,
Please excuse the dumbness but we are trying to learn.
We have just purchased a winchester m70 375H&H this gun must be a new model as it has no sights it has only bases for a scope.
We normally only hunt in bushveld(thicks) and would like to put some sights on.
Now for the tricky bit we donot have any gunsmiths as such and any attempt would be a DIY job, is there any sights anyone can reccommend?
Regards
 
Posts: 228 | Location: Zambia | Registered: 25 September 2003Reply With Quote
one of us
Picture of D Humbarger
posted Hide Post
Zambian your M70 has no sight & no plugged sight screw holes?Frowner Then this is indeed a task for a gunsmith to undertake.



Doug Humbarger
NRA Life member
Tonkin Gulf Yacht Club 72'73.
Yankee Station

Try to look unimportant. Your enemy might be low on ammo.
 
Posts: 8351 | Location: Jennings Louisiana, Arkansas by way of Alabama by way of South Carloina by way of County Antrim Irland by way of Lanarkshire Scotland. | Registered: 02 November 2001Reply With Quote
one of us
posted Hide Post
If your rifle is not pre-drilled and tapped, you will need a GOOD skill to install succesfully open sights on it. You will have to EXACTLY drill and tap (usually 2 + 2 holes) to avoid misalignement between the front and rear sight and from the two sights and the line of sight.....think it over! - Lorenzo
 
Posts: 1459 | Location: north-west Italy | Registered: 16 April 2002Reply With Quote
One of Us
posted Hide Post
It doesn't have to be that difficult. Is it drilled for a receiver sight? If so start with a Lyman and a barrel-band front sight that matches your barrel diameter. Usually these are soft soldered and use a single set screw in the dovetail slot to lock them in place. Start with the set screw just snug (may have to get a short screw), no indent in the barrel. Do a little trial and error shooting, rotating front base until the gun is shooting to to the sights, then mark location, carefully drill dimple and set the sight. You could probably use a good epoxy instead of soft solder it that is a problem. A lot of fooling around but not impossible for a good craftsman. Of course a 'smith' with a jig could probably do this in 30 min. If Brownells is an option they would have everything you would need.
C.G.B.
 
Posts: 1103 | Registered: 25 January 2005Reply With Quote
one of us
Picture of D Humbarger
posted Hide Post
cgbach that is a great idea but the new M70s i've seen arn't even drilled & tapped for peep sights. Roll Eyes



Doug Humbarger
NRA Life member
Tonkin Gulf Yacht Club 72'73.
Yankee Station

Try to look unimportant. Your enemy might be low on ammo.
 
Posts: 8351 | Location: Jennings Louisiana, Arkansas by way of Alabama by way of South Carloina by way of County Antrim Irland by way of Lanarkshire Scotland. | Registered: 02 November 2001Reply With Quote
One of Us
posted Hide Post
The stock is set up for a scope. Iron sights will be to low. It will be very uncomfortable to shoot. I would order a low power scope, like a Leupold 2X. You can do that on the internet. Get some good rings, install it, and go hunting. It wil be much simpler than any iron sight solution. You will find the low power scope to be faster than iron sights,......really. Unless you are after nostalgia or shooting an antique, a scope is better. The idea of iron sights and heavy round nosed bulelts for brush hunting are myths of the past. The Leupold, or equivelent, 2X or the 1.5X-4x are good stuff. Do not buy a cheap scope. Get a top quality one. Personally I would go for the fixed power.
 
Posts: 508 | Registered: 20 January 2005Reply With Quote
one of us
posted Hide Post
I second Scota's suggestion 100% - Lorenzo
 
Posts: 1459 | Location: north-west Italy | Registered: 16 April 2002Reply With Quote
One of Us
posted Hide Post
quote:
Originally posted by zambian:
Good all,
Please excuse the dumbness but we are trying to learn.
We have just purchased a winchester m70 375H&H this gun must be a new model as it has no sights it has only bases for a scope.
We normally only hunt in bushveld(thicks) and would like to put some sights on.
Now for the tricky bit we donot have any gunsmiths as such and any attempt would be a DIY job, is there any sights anyone can reccommend?
Regards


Zambian,

NECG sells a very nice adjustable rear peep sight that clamps right to a weaver style scope base. You can buy them directly from NECG or Brownells. You can also buy a banded/ramp front sight matched to your barrel diameter and contour that can be epoxied to the barrel.

As long as you have the capability, and ability, to level the rifle and square it up this shouldn’t be all that hard for a guy with a little better than average mechanical/handyman skills.
 
Posts: 4574 | Location: Valencia, California | Registered: 16 March 2005Reply With Quote
one of us
posted Hide Post
Don't know about it having to be a new model to have no iron sights. My .458 was made in 1976
and shows no sign of ever having iron sights.
It is drilled for a rear open and an action mounted peep.
A real disapointment at first then I reminded myself that I can't see iron any more, so looks like the scope stays on.
John L.
 
Posts: 2355 | Location: Australia | Registered: 14 November 2004Reply With Quote
  Powered by Social Strata  
 


Copyright December 1997-2023 Accuratereloading.com


Visit our on-line store for AR Memorabilia