THE ACCURATERELOADING.COM GUNSMITHING FORUM

Accuratereloading.com    The Accurate Reloading Forums    THE ACCURATE RELOADING.COM FORUMS  Hop To Forum Categories  Guns, Politics, Gunsmithing & Reloading  Hop To Forums  Gunsmithing    Looking for a CNC shop to make a run of gun parts

Moderators: jeffeosso
Go
New
Find
Notify
Tools
Reply
  
Looking for a CNC shop to make a run of gun parts
 Login/Join
 
One Of Us
Picture of new_guy
posted
Anyone know of a small shop that would take on small runs of one-offs?


www.heymusa.com


HSC Booth # 306
SCI Booth # 3947
 
Posts: 4025 | Registered: 28 May 2004Reply With Quote
One of Us
Picture of Mike_Dettorre
posted Hide Post
PM sent


Mike

Never under estimate the internet community's ability to reply to your post with their personal rant about their tangentially related, single occurrence issue.



What I have learned on AR, since 2001:
1. The proper answer to: Where is the best place in town to get a steak dinner? is…You should go to Mel's Diner and get the fried chicken.
2. Big game animals can tell the difference between .015 of an inch in diameter, 15 grains of bullet weight, and 150 fps.
3. There is a difference in the performance of two identical projectiles launched at the same velocity if they came from different cartridges.
4. While a double rifle is the perfect DGR, every 375HH bolt gun needs to be modified to carry at least 5 down.
5. While a floor plate and detachable box magazine both use a mechanical latch, only the floor plate latch is reliable. Disregard the fact that every modern military rifle uses a detachable box magazine.
6. The Remington 700 is unreliable regardless of the fact it is the basis of the USMC M40 sniper rifle for 40+ years with no changes to the receiver or extractor and is the choice of more military and law enforcement sniper units than any other rifle.
7. PF actions are not suitable for a DGR and it is irrelevant that the M1, M14, M16, & AK47 which were designed for hunting men that can shoot back are all PF actions.
8. 95 deg F in Africa is different than 95 deg F in TX or CA and that is why you must worry about ammunition temperature in Africa (even though most safaris take place in winter) but not in TX or in CA.
9. The size of a ding in a gun's finish doesn't matter, what matters is whether it’s a safe ding or not.
10. 1 in a row is a trend, 2 in a row is statistically significant, and 3 in a row is an irrefutable fact.
11. Never buy a WSM or RCM cartridge for a safari rifle or your go to rifle in the USA because if they lose your ammo you can't find replacement ammo but don't worry 280 Rem, 338-06, 35 Whelen, and all Weatherby cartridges abound in Africa and back country stores.
12. A well hit animal can run 75 yds. in the open and suddenly drop with no initial blood trail, but the one I shot from 200 yds. away that ran 10 yds. and disappeared into a thicket and was not found was lost because the bullet penciled thru. I am 100% certain of this even though I have no physical evidence.
13. A 300 Win Mag is a 500 yard elk cartridge but a 308 Win is not a 300 yard elk cartridge even though the same bullet is travelling at the same velocity at those respective distances.
 
Posts: 10138 | Location: Loving retirement in Boise, ID | Registered: 16 December 2003Reply With Quote
One of Us
posted Hide Post
It's all about how much $$$ you want to spend. CNC is CNC and how much you want to spend on the set up, etc. If you can supply the geometry, well that's that. If not?
 
Posts: 160 | Location: Homer, AK | Registered: 11 April 2013Reply With Quote
Administrator
posted Hide Post
For basic parts that do not require the use of many different tools, programming is not difficult.


www.accuratereloading.com
Instagram : ganyana2000
 
Posts: 68793 | Location: Dubai, UAE | Registered: 08 January 1998Reply With Quote
new member
posted Hide Post
PM sent
 
Posts: 11 | Registered: 06 November 2019Reply With Quote
One of Us
Picture of custombolt
posted Hide Post
Please clarify your needs.
Small run (plural) or several single (different) parts?


Life itself is a gift. Live it up if you can.
 
Posts: 5239 | Location: Near Hershey PA | Registered: 12 October 2012Reply With Quote
  Powered by Social Strata  
 

Accuratereloading.com    The Accurate Reloading Forums    THE ACCURATE RELOADING.COM FORUMS  Hop To Forum Categories  Guns, Politics, Gunsmithing & Reloading  Hop To Forums  Gunsmithing    Looking for a CNC shop to make a run of gun parts

Copyright December 1997-2023 Accuratereloading.com


Visit our on-line store for AR Memorabilia