THE ACCURATERELOADING.COM GUNSMITHING FORUM


Moderators: jeffeosso
Go
New
Find
Notify
Tools
Reply
  
Rings for Brno & CZ
 Login/Join
 
one of us
posted
The
Take a look at www.huntamerica.com/talley/
CZ 550 or BRNO 602, 1", Low Ht., QD w/Lever Lock $109.95

Talley seams to manufacture ring for CZ. Does the rings attaches to the integral dove tail on the CZ? Or do you have to have a Tallay base installed?
What do you think about them? Have any one tried these rings?
At what side are the leavers? Left or right?
Does anyone have a picture of these rings.

Regards
Johan

[ 07-10-2003, 17:12: Message edited by: 375HH ]
 
Posts: 87 | Location: Sweden | Registered: 14 September 2001Reply With Quote
one of us
Picture of Longbob
posted Hide Post
Talleys are either base specific or they are ring specific. Their "standard" rings will attach to all of their bases. In the case of the Talley CZ rings, they will attach like the normal CZ rings to the integral base of the CZ action.
 
Posts: 3512 | Location: Denton, TX | Registered: 01 June 2001Reply With Quote
one of us
posted Hide Post
Longbob
Are the Talley rings for CZ rock steady?
Do they return to zero?

/Johan

[ 07-10-2003, 17:16: Message edited by: 375HH ]
 
Posts: 87 | Location: Sweden | Registered: 14 September 2001Reply With Quote
<K9>
posted
Johan
Here's a link to Jack Belk's album. There are a few pics of Talley's for Brno/CZ on nextjoe's (another member here) gun.
Talley look good and have a stellar reputation on this forum........ Wish they made them in 30mm for the Brno's.. [Frown]

Jack Belk's work of art

Cheers
K9
 
Reply With Quote
<JOHAN>
posted
Well
Talley are damn good rings and I must say that I like them much. I really hate that warne closed down their premium line of Brno mounts.

/ JOHAN

[ 07-10-2003, 23:43: Message edited by: JOHAN ]
 
Reply With Quote
one of us
Picture of Longbob
posted Hide Post
Johan,

Sorry for the delay. All of the Talley rings that I have are rock solid and return to zero without fail. I have them on most of my rifles including the QD's on a 375 H&H, 458 Lott, and 460 Weatherby. I have a CZ 416 Rigby that is being restocked right now and I will use the Talleys on it. Most likely, I will not use the levers on the CZ.
 
Posts: 3512 | Location: Denton, TX | Registered: 01 June 2001Reply With Quote
one of us
Picture of Longbob
posted Hide Post
I meant that last response to be for 375HH. Sorry about that Johan. [Smile]
 
Posts: 3512 | Location: Denton, TX | Registered: 01 June 2001Reply With Quote
<JOHAN>
posted
Gentlemen

Can any of you who own a 550 or a Brno 600 messure it and see how wide the milled in bases are?

I'm not sure that they are the same on all the modells

Thanks for any help

/ JOHAN
 
Reply With Quote
one of us
Picture of HunterJim
posted Hide Post
Johan,

I think they are 19 mm, at least the BRNO M602 is.

jim
 
Posts: 4166 | Location: San Diego, CA USA | Registered: 14 November 2001Reply With Quote
  Powered by Social Strata  
 


Copyright December 1997-2023 Accuratereloading.com


Visit our on-line store for AR Memorabilia