THE ACCURATERELOADING.COM GUNSMITHING FORUM


Moderators: jeffeosso
Go
New
Find
Notify
Tools
Reply
  
How to fill side mount holes
 Login/Join
 
one of us
posted
Purchased a pre-64 model 70 with 4 holes in left side of receiver from old weaver side mount. Any suggestion on how to fill or who to do the work?


"Only two defining forces have ever offered to die for you; Jesus Christ and the American Soldier. One died for your sins, the other for your freedom...."
 
Posts: 426 | Location: Yakima, Washington, USA | Registered: 30 March 2002Reply With Quote
One of Us
Picture of Mike_Dettorre
posted Hide Post
I am sure you will get lots of good advice on here.

I thought there was a thread a while back of somebody showing the process of first chamfering/counter sinking the hole, then filling them with a long screw then cutting the screw head off so a small amount is exposed above the hole, then peening it down and polishing it smooth, and re-blueing.


Mike

Legistine actu quod scripsi?

Never under estimate the internet community's ability to reply to your post with their personal rant about their tangentially related, single occurrence issue.




What I have learned on AR, since 2001:
1. The proper answer to: Where is the best place in town to get a steak dinner? is…You should go to Mel's Diner and get the fried chicken.
2. Big game animals can tell the difference between .015 of an inch in diameter, 15 grains of bullet weight, and 150 fps.
3. There is a difference in the performance of two identical projectiles launched at the same velocity if they came from different cartridges.
4. While a double rifle is the perfect DGR, every 375HH bolt gun needs to be modified to carry at least 5 down.
5. While a floor plate and detachable box magazine both use a mechanical latch, only the floor plate latch is reliable. Disregard the fact that every modern military rifle uses a detachable box magazine.
6. The Remington 700 is unreliable regardless of the fact it is the basis of the USMC M40 sniper rifle for 40+ years with no changes to the receiver or extractor and is the choice of more military and law enforcement sniper units than any other rifle.
7. PF actions are not suitable for a DGR and it is irrelevant that the M1, M14, M16, & AK47 which were designed for hunting men that can shoot back are all PF actions.
8. 95 deg F in Africa is different than 95 deg F in TX or CA and that is why you must worry about ammunition temperature in Africa (even though most safaris take place in winter) but not in TX or in CA.
9. The size of a ding in a gun's finish doesn't matter, what matters is whether it’s a safe ding or not.
10. 1 in a row is a trend, 2 in a row is statistically significant, and 3 in a row is an irrefutable fact.
11. Never buy a WSM or RCM cartridge for a safari rifle or your go to rifle in the USA because if they lose your ammo you can't find replacement ammo but don't worry 280 Rem, 338-06, 35 Whelen, and all Weatherby cartridges abound in Africa and back country stores.
12. A well hit animal can run 75 yds. in the open and suddenly drop with no initial blood trail, but the one I shot from 200 yds. away that ran 10 yds. and disappeared into a thicket and was not found was lost because the bullet penciled thru. I am 100% certain of this even though I have no physical evidence.
13. A 300 Win Mag is a 500 yard elk cartridge but a 308 Win is not a 300 yard elk cartridge even though the same bullet is travelling at the same velocity at those respective distances.
 
Posts: 10181 | Location: Loving retirement in Boise, ID | Registered: 16 December 2003Reply With Quote
One of Us
posted Hide Post
quote:
"Nearly all men can stand adversity, but if you want to test a man's character, give him power." Abraham Lincoln

A good measure of a person is how they treat those that can do nothing for them.


When the USA was formed, a popular phrase was "All men would be tyrants."

I think the balance of power came out of that.
 
Posts: 9043 | Location: on the rock | Registered: 16 July 2005Reply With Quote
One of Us
posted Hide Post
These jobs are always a bit of a nightmare...but I use taper pins, ream the holes, drive them from the inside with a BIG whammer, they tig the outside. That leaves the lettering. Roger Ferrell has a pattern for photo etching to re-create the logo...damn good!
 
Posts: 2221 | Location: Tacoma, WA | Registered: 31 October 2003Reply With Quote
One of Us
posted Hide Post
Often here in UK make an overlong length of threaded rod the same pitch etc. as the female thread. Screw it in, cut it off. Ditto next three holes. Gring/file down, polish if required or wanted and refinish.

The other way, which looks less "messy" is to make a screw like a grub screw and screw that in and turn all the slots level. Big advantage is you don't touch the original blue and one day you might want that sight mount back on it!
 
Posts: 6824 | Location: United Kingdom | Registered: 18 November 2007Reply With Quote
One of Us
posted Hide Post
Use taper pins made out of O1 tool steel. Drive them in and finish them off. This was told to me by Herman Waldron and the last one I did I had trouble finding the holes myself after I did it.
 
Posts: 328 | Location: Oklahoma | Registered: 20 June 2006Reply With Quote
One of Us
posted Hide Post
quote:
Originally posted by Nick Hughes:
Use taper pins made out of O1 tool steel. Drive them in and finish them off. This was told to me by Herman Waldron and the last one I did I had trouble finding the holes myself after I did it.


What did you do with the logo/lettering?
 
Posts: 2221 | Location: Tacoma, WA | Registered: 31 October 2003Reply With Quote
One of Us
posted Hide Post
I have a local engraver touch up the logo where the pin goes through.
 
Posts: 328 | Location: Oklahoma | Registered: 20 June 2006Reply With Quote
one of us
posted Hide Post
Thanks everyone. If I decide I want to fill the holes would either Nick or Duane take on the job?


"Only two defining forces have ever offered to die for you; Jesus Christ and the American Soldier. One died for your sins, the other for your freedom...."
 
Posts: 426 | Location: Yakima, Washington, USA | Registered: 30 March 2002Reply With Quote
One of Us
posted Hide Post
Sure,

Maybe I could document the job and post it on here.
 
Posts: 328 | Location: Oklahoma | Registered: 20 June 2006Reply With Quote
  Powered by Social Strata  
 


Copyright December 1997-2023 Accuratereloading.com


Visit our on-line store for AR Memorabilia