21 September 2014, 01:33
Gracedogslippery stock
I just replaced the factory stock (synthetic) on my pre-64 model 70 with an aftermarket laminated model. I have wanted to go back to wood for some time, but wanted to have something more stable than a run of the mill wooden stock, hence the laminated option. The stock itself was exactly what I was looking for, with nearly flawless wood to metal fit, and proportions that fit my build far better than the original. I opted not to have it checkered, since I don't care that much for the look. Anyway, the only negative thing that I can say about this stock is that it is so smooth that I am concerned about dropping it. I read somewhere that there is a new transparent spray-on product that can alleviate this problem. Do any of you out there have any suggestions?
21 September 2014, 02:02
craigsterHave seen this,
http://www.rustoleum.com/about...um-anti-slip-spray/, but haven't used it. Might be what you're looking for.
21 September 2014, 02:11
dpcdI have used wrinkle paint but it is black.
21 September 2014, 10:51
ted thornI have scatebard tape on my laminated Ruger
You may be able to see it in this picture
21 September 2014, 23:37
Wstrnhuntrquote:
Originally posted by Gracedog:
I just replaced the factory stock (synthetic) on my pre-64 model 70 with an aftermarket laminated model. I have wanted to go back to wood for some time, but wanted to have something more stable than a run of the mill wooden stock, hence the laminated option. The stock itself was exactly what I was looking for, with nearly flawless wood to metal fit, and proportions that fit my build far better than the original. I opted not to have it checkered, since I don't care that much for the look. Anyway, the only negative thing that I can say about this stock is that it is so smooth that I am concerned about dropping it. I read somewhere that there is a new transparent spray-on product that can alleviate this problem. Do any of you out there have any suggestions?
When I painted my boat I used some grip grit from Home depot on the step surfaces. You just mix it in with the paint. It worked pretty well. I have never thought of trying it, but I expect it would work with some tung oil on a stock in the grip areas.
22 September 2014, 01:10
GrenadierYou should have gotten it checkered.
22 September 2014, 01:32
farbedoThis is what I did.
Get sand from a bridal or hobby store that matches the color of your stock. Clean and tape off the area you want to texture. Spray it with Spar Varnish (I used Helmsman from Minwax). Sprinkle the sand on while the varnish is wet, and pat it into the wet varnish with your hand. Let dry, and overcoat with vanish one or two times. It doesn't take much sand, you don't want to coat it, just add texture.
This has held up well for me and it looks like it is supposed to be there.
Jeremy
22 September 2014, 05:05
youngoutdoorsI used Rustoleum Multi-color Textured in Autumn Brown for a brown laminated stock and taped off the stock to leave a checkering pattern. Just a light coat will do the trick and you can still see the grain of the wood through the Rustoleum. Works great.
God Bless, Louis
22 September 2014, 14:22
GracedogThanks for the ideas. I also found out about a clear spray from "Slipdoctors" that may work. Thanks for the help.
22 September 2014, 18:18
sroseRub it down with a good floor wax or surf board wax. Protects stock and gives it a grippy feel. I also use it on metal to prevent rust.
22 September 2014, 18:39
Doglegquote:
Originally posted by srose:
Rub it down with a good floor wax or surf board wax. Protects stock and gives it a grippy feel. I also use it on metal to prevent rust.
Yes, non slip wax takes away that slick feeling.
22 September 2014, 21:23
Snellstromquote:
Originally posted by farbedo:
This is what I did.
Get sand from a bridal or hobby store that matches the color of your stock. Clean and tape off the area you want to texture. Spray it with Spar Varnish (I used Helmsman from Minwax). Sprinkle the sand on while the varnish is wet, and pat it into the wet varnish with your hand. Let dry, and overcoat with vanish one or two times. It doesn't take much sand, you don't want to coat it, just add texture.
This has held up well for me and it looks like it is supposed to be there.
Jeremy
Great idea!
23 September 2014, 09:27
hoghuntingBrownells has a spray grit that also comes in clear to show your laminated stock:
http://www.brownells.com/gunsm...y-grit-prod1140.aspx23 September 2014, 16:16
7mmfreakYou can also use a normal can of satin or flat clear and hold it just far enough away from the stock that you are dusting it and it will give it a very light texture. I have used this method, spray grit, pottery texture, and stippling. Each has it's place but I would probably just hit it with clear like I first mentioned if you want the stock to look the same but feel less slick.