THE ACCURATERELOADING.COM GUNSMITHING FORUM


Moderators: jeffeosso
Go
New
Find
Notify
Tools
Reply
  
How do I unloctite...red loctite
 Login/Join
 
One of Us
Picture of Mike_Dettorre
posted
...can get the rings off a scope...


Mike

Legistine actu quod scripsi?

Never under estimate the internet community's ability to reply to your post with their personal rant about their tangentially related, single occurrence issue.




What I have learned on AR, since 2001:
1. The proper answer to: Where is the best place in town to get a steak dinner? is…You should go to Mel's Diner and get the fried chicken.
2. Big game animals can tell the difference between .015 of an inch in diameter, 15 grains of bullet weight, and 150 fps.
3. There is a difference in the performance of two identical projectiles launched at the same velocity if they came from different cartridges.
4. While a double rifle is the perfect DGR, every 375HH bolt gun needs to be modified to carry at least 5 down.
5. While a floor plate and detachable box magazine both use a mechanical latch, only the floor plate latch is reliable. Disregard the fact that every modern military rifle uses a detachable box magazine.
6. The Remington 700 is unreliable regardless of the fact it is the basis of the USMC M40 sniper rifle for 40+ years with no changes to the receiver or extractor and is the choice of more military and law enforcement sniper units than any other rifle.
7. PF actions are not suitable for a DGR and it is irrelevant that the M1, M14, M16, & AK47 which were designed for hunting men that can shoot back are all PF actions.
8. 95 deg F in Africa is different than 95 deg F in TX or CA and that is why you must worry about ammunition temperature in Africa (even though most safaris take place in winter) but not in TX or in CA.
9. The size of a ding in a gun's finish doesn't matter, what matters is whether it’s a safe ding or not.
10. 1 in a row is a trend, 2 in a row is statistically significant, and 3 in a row is an irrefutable fact.
11. Never buy a WSM or RCM cartridge for a safari rifle or your go to rifle in the USA because if they lose your ammo you can't find replacement ammo but don't worry 280 Rem, 338-06, 35 Whelen, and all Weatherby cartridges abound in Africa and back country stores.
12. A well hit animal can run 75 yds. in the open and suddenly drop with no initial blood trail, but the one I shot from 200 yds. away that ran 10 yds. and disappeared into a thicket and was not found was lost because the bullet penciled thru. I am 100% certain of this even though I have no physical evidence.
13. A 300 Win Mag is a 500 yard elk cartridge but a 308 Win is not a 300 yard elk cartridge even though the same bullet is travelling at the same velocity at those respective distances.
 
Posts: 10169 | Location: Loving retirement in Boise, ID | Registered: 16 December 2003Reply With Quote
one of us
posted Hide Post
If you are sure its lock tight I would take a soldering iron and heat the screws the that should loosen it.
 
Posts: 19736 | Location: wis | Registered: 21 April 2001Reply With Quote
One of Us
posted Hide Post
Heat gun.
 
Posts: 985 | Registered: 06 February 2005Reply With Quote
One of Us
Picture of STINGER
posted Hide Post
JUST MY PERSONAL OPINION BUT I THINK THE SOLDERING IRON IS A MORE VIABLE SOLUTION. IT'S WHAT I USE ALL THE TIME.


PLEASE EXCUSE CAPS, HANDICAPPED TYPIST.

"THE" THREAD KILLER

IT'S OK......I'VE STARTED UP MY MEDS AGAIN. THEY SHOULD TAKE EFFECT IN ABOUT A WEEK. (STACI-2006)

HAPPY TRAILS

HANDLOADS ARE LIKE UNDERWEAR....BE CAREFUL WHO YOU SWAP WITH.

BILL
 
Posts: 479 | Location: MINOT, NORTH DAKOTA | Registered: 24 January 2005Reply With Quote
One of Us
posted Hide Post
Mike
The method I used is to get a screwdriver that will fit the screw, and one you don't mind getting hot. Gently heat the screwdriver a couple of inches above the screw, and let the heat travel down the shaft, while maintaining some pressure. When the screw starts moving take the heat off and unscrew it. I works every time for me and it does not take a lot of heat.


Never rode a bull, but have shot some.

NRA life member
NRA LEO firearms instructor (retired)
NRA Golden Eagles member
 
Posts: 1513 | Location: Camp Verde, AZ | Registered: 13 December 2005Reply With Quote
one of us
Picture of Kyler Hamann
posted Hide Post
Hey Mike,

If you're treating your guns that poorly (using RED Locktite on scope rings) you should just give them to a better home. Possibly someone on the Central Coast....

Wink

Kyler


___________________________
www.boaring.com
_____
 
Posts: 2516 | Location: Central Coast of CA | Registered: 10 January 2002Reply With Quote
One of Us
posted Hide Post
quote:
Originally posted by Rolland:
Mike
The method I used is to get a screwdriver that will fit the screw, and one you don't mind getting hot. Gently heat the screwdriver a couple of inches above the screw, and let the heat travel down the shaft, while maintaining some pressure. When the screw starts moving take the heat off and unscrew it. I works every time for me and it does not take a lot of heat.

I like your idea the best. thumb
 
Posts: 985 | Registered: 06 February 2005Reply With Quote
one of us
posted Hide Post
Hi: I use a method recommended by Brownell's gunsmiths. Use a Bernzomatic propane torch.
Heat the area until it smokes, red locktite will burn off at 300 degrees, its said. Then just use whatever you use to turn the screws...allen wrench or whatever the fitting is. I've done it, and heat is the only thing that will remove red lock tite that I know of. If you care careful, (please do!),just keep the heat applied only where needed.
I've done this many times on gun scope bases & mounts where someone had used red lock tite & found it works. Best Regards, Tom
 
Posts: 262 | Location: Wyoming, U.S.A. | Registered: 11 November 2004Reply With Quote
one of us
posted Hide Post
For auto engine fasteners you tighten the bolt, which turns the locktite to red powder allowing you to back the bolt out.
Perhaps this only the procedure for the larger thread perches.
 
Posts: 4799 | Location: Lehigh county, PA | Registered: 17 October 2002Reply With Quote
one of us
posted Hide Post
I used red loc-tite on the collapsible stock of my AR-15 carbine. I had to use an 18" pipe wrench to loosen that thing. I buggered-up the lock ring, the buffer tube and the receiver plate. Never again...
 
Posts: 2758 | Location: Fernley, NV-- the center of the shootin', four-wheelin', ATVin' and dirt-bikin' universe | Registered: 28 May 2003Reply With Quote
new member
posted Hide Post
Locktite is great stuff. But you need to know what type is used for what application. Use the red if you don't want to take it appart, EVER! I use 242 (med strength-blue) on 22's up to magnums. On magnums I use high strength (272-4 purple) but would not hesitate to use 242 on mags, pistols or rifles. Preclean with acetone, let dry an apply. You don't need much either. One drop applied to the bottom 2nd or 3rd thread. Works ever time and will come loose without heat.

Hope this helps


GT
 
Posts: 31 | Registered: 27 June 2004Reply With Quote
  Powered by Social Strata  
 


Copyright December 1997-2023 Accuratereloading.com


Visit our on-line store for AR Memorabilia