THE ACCURATERELOADING.COM GUNSMITHING FORUM


Moderators: jeffeosso
Go
New
Find
Notify
Tools
Reply
  
Rugar 77 tang safety 220 Swift
 Login/Join
 
one of us
Picture of alleyyooper
posted
Im having a problem with the trigger on this rifle. I bought it used a while back shot three boxes of factory loads thru it fine. On the fourth box the trigger ?like locked up, felt hard and the fireing pin never moved. Recocked it once to no avail. Second recock it fired. Fired for six rounds and did it again. Recocked ita half dozen times then and nothing. Still acts like some thing is locked up.

Anybody able to advise me on a simple fix?

Thank you
Big Grin Al


Garden View Apiaries where the view is as sweet as the honey.
 
Posts: 505 | Location: Michigan, U.S.A. | Registered: 04 December 2001Reply With Quote
one of us
Picture of alleyyooper
posted Hide Post
NO IDEAS?????

Big Grin Al


Garden View Apiaries where the view is as sweet as the honey.
 
Posts: 505 | Location: Michigan, U.S.A. | Registered: 04 December 2001Reply With Quote
One of Us
posted Hide Post
The kindest advice you can receive is to take it to a Gunsmith.
 
Posts: 718 | Location: Utah | Registered: 14 September 2008Reply With Quote
One of Us
posted Hide Post
sounds like you sear engagement is off. the ruger trigger is rather simple and not adjustable. if the sear engagement is off you are probably in the market for a trigger
 
Posts: 13466 | Location: faribault mn | Registered: 16 November 2004Reply With Quote
One of Us
posted Hide Post
I didn't have the problem on mine that you are describing.

In my case, it might fire when the saftey was dis-engaged, or a not so sharp blow to the stock would also set it off.

The trigger only has one screw adjustment on it, and it sets both sear engagment and lbs pull on it. When I got it so that it wouldn't fire, I was then about a 5 lb trigger.

I ended up replacing it with a timney.
 
Posts: 270 | Location: Cedar Rapids IA | Registered: 02 November 2006Reply With Quote
one of us
Picture of alleyyooper
posted Hide Post
Since I bought it used I can not say if some one messed with the trigger or not.
I'm thinking I should get in touch with Rugar and see what they have to say.
I have a Rugar 77 tang safety in 243 I bought new. The trigger on it is real nice.

Big Grin Al


Garden View Apiaries where the view is as sweet as the honey.
 
Posts: 505 | Location: Michigan, U.S.A. | Registered: 04 December 2001Reply With Quote
one of us
posted Hide Post
Are you sure that the action screws are not over-tightened? Maybe debris in the bolt or a broken firing pin spring. The side of my bolts on my older 77's are machined slotted. Easy to lubricate but could let dirt/debris in.
 
Posts: 323 | Location: Northeastern, PA | Registered: 21 June 2002Reply With Quote
one of us
posted Hide Post
I have worked on the Ruger 77 Tang safety style triggers many times.

First of all they are not a simple one adjustment screw trigger. They have 3 differant adjustment screws (one is hidden) and are rather complex compared to conventional designs like Remington. Actually if you study them carefully you will realize they are a near genius design by Ruger.

Because of their complex design they are often really screwed up by amatuers.

Nomo4me gave you the best advice, to take it to a competant gunsmith.

From what you describe, somone has tinkered with the sear engagement which affects the overtravel.

I think Ruger went to their terrible over simplified design they have now due to too many people that did not know what they were doing tinkering with them. This was their attempt to make them idiot proof.


Craftsman
 
Posts: 1551 | Location: North Texas | Registered: 11 February 2001Reply With Quote
one of us
Picture of alleyyooper
posted Hide Post
Notice to Owners of Ruger
M-77 Bolt Action Rifles
The trigger overtravel adjustment set
screw (shown on right) in a few of these
rifles may not be securely tightened and
may move too readily. This change in
original adjustment can, in extre m e
cases, either cause the rifle to fire unexpectedly
(with the safety “off) or cause
the rifle to not fire at all. This may occur
suddenly, without warning.
Current production rifles have this
set screw permanently secured. These
rifles have a “T” inscribed on the underside
of the bolt handle. This condition cannot occur in any of our other
firearms, such as the 77/22, 10/22, No. 1, No. 3, or the .44 Carbine, as their
trigger mechanisms differ.
For your safety, we ask that all owners of M-77 rifles (except those with a
“T” underneath the bolt handle) contact us, using the coupon below.
You will receive a new locking screw that will replace your present overtravel
adjustment set screw and detailed instructions for quick, easy installation.
There is no charge for this service and replacing the screw will have
no adverse effect on trigger pull.
Do not use your M-77 rifle until you have received and installed the
replacement screw.
SINGLE COPIES OF INSTRUCTION MANUALS FOR ALLMODELS OF RUGER FIREARMS ARE
AVAILABLE ON REQUEST - PLEASE SPECIFYMODELFOR WHICH YOU REQUIRE A MANUAL.
STURM, RUGER & Company, Inc.
140 Lacey Place
Southport, Connecticut 06490 U.S.A.
ALL RUGER FIREARMS ARE DESIGNED AND MANUFACTURED IN RUGER FACTORIES IN THE UNITED STATES OF AMERICA
Please affix to a postcard and mail to:
Sturm, Ruger & Company, Inc., Dept. M-77
140 Lacey Place, Southport, Connecticut 06490
NAME
(Please Print)
STREET OR P.O. BOX
CITY STATE ZIP
Number of M-77’s owned: List serial numbers here:
Ruger M-77 Rifle

Big Grin Al


Garden View Apiaries where the view is as sweet as the honey.
 
Posts: 505 | Location: Michigan, U.S.A. | Registered: 04 December 2001Reply With Quote
one of us
Picture of alleyyooper
posted Hide Post
Mine has that T on the under side of the bolt.

Big Grin Al


Garden View Apiaries where the view is as sweet as the honey.
 
Posts: 505 | Location: Michigan, U.S.A. | Registered: 04 December 2001Reply With Quote
  Powered by Social Strata  
 


Copyright December 1997-2023 Accuratereloading.com


Visit our on-line store for AR Memorabilia