THE ACCURATERELOADING.COM GUNSMITHING FORUM


Moderators: jeffeosso
Go
New
Find
Notify
Tools
Reply
  
Rem 700 bolt face opening- w/o sako extractor?
 Login/Join
 
One of Us
posted
Can the bolt face of a 700 for standard rim-sized magnums (.532ish) be opened up for a 416 rigby rim (.590) w/o going to a sako style extractor?
 
Posts: 54 | Location: Newport, WA-Susanville, CA | Registered: 04 September 2008Reply With Quote
One of Us
Picture of D99
posted Hide Post
The m700 is a great action, however it is limited by what it can be.

Cutting into the rim face and putting the sako extractor in comprimises the full strength of the action.

I would never do it, it was designed the way it was for a reason. Some will dissagree with me, but you can't cut that much out of a M700 without sacraficing a lot of steel.
 
Posts: 4729 | Location: Australia | Registered: 06 February 2005Reply With Quote
One of Us
posted Hide Post
Oh come on, it only occupies another 13% of the bolt nose area. Wink
And I'm trying to NOT go to the Sako extractor, I understand the recessed/safety breech design and how it would defeat that concept.
 
Posts: 54 | Location: Newport, WA-Susanville, CA | Registered: 04 September 2008Reply With Quote
One of Us
posted Hide Post
The problem is no one makes a Rigby size Remington extractor. Sure you could bend a mag extractor and hope it works, but your your already messing with the well known weak link of the 700. Sako it and enjoy it's reliability.
 
Posts: 460 | Location: Auburn CA. | Registered: 25 March 2007Reply With Quote
one of us
posted Hide Post
Just look at what the Remington factory does to build their 338 Lapua sniper rifle. They use a Sako or M16 (I forget which) on it. I figure if they could have kept the normal setup, they would have. It would just get too thin to work.
 
Posts: 187 | Location: Nuevo Mexico | Registered: 15 May 2001Reply With Quote
One of Us
Picture of D99
posted Hide Post
You also won't see any Remington M700 338 Lapua factory sniper rifles in the hands of US military folks. They won't pass the military quality assurance facilities.

All 338 Lapua sniper rifles in the hands of our military are custom built affairs made by the Navy in Crane or by the Marines in Quanitico.
 
Posts: 4729 | Location: Australia | Registered: 06 February 2005Reply With Quote
One of Us
Picture of Mike_Dettorre
posted Hide Post
I had a Lazzeroni short action 338 built on a 700 and the case head on that is .580. They did use a sako extractor.

It just barely fit on the bolt face.

I don't know how you could get a rigby in the bolt face at all.

Also realize you will not be able to "eject" a loaded round.

The round is simply too heavy. The ejector plunger will try and throw it but there is not enough "umpf" and it will hang up and end up just lying in the open ejection port.

It's not really a big deal just annoying.


Mike

Legistine actu quod scripsi?

Never under estimate the internet community's ability to reply to your post with their personal rant about their tangentially related, single occurrence issue.




What I have learned on AR, since 2001:
1. The proper answer to: Where is the best place in town to get a steak dinner? is…You should go to Mel's Diner and get the fried chicken.
2. Big game animals can tell the difference between .015 of an inch in diameter, 15 grains of bullet weight, and 150 fps.
3. There is a difference in the performance of two identical projectiles launched at the same velocity if they came from different cartridges.
4. While a double rifle is the perfect DGR, every 375HH bolt gun needs to be modified to carry at least 5 down.
5. While a floor plate and detachable box magazine both use a mechanical latch, only the floor plate latch is reliable. Disregard the fact that every modern military rifle uses a detachable box magazine.
6. The Remington 700 is unreliable regardless of the fact it is the basis of the USMC M40 sniper rifle for 40+ years with no changes to the receiver or extractor and is the choice of more military and law enforcement sniper units than any other rifle.
7. PF actions are not suitable for a DGR and it is irrelevant that the M1, M14, M16, & AK47 which were designed for hunting men that can shoot back are all PF actions.
8. 95 deg F in Africa is different than 95 deg F in TX or CA and that is why you must worry about ammunition temperature in Africa (even though most safaris take place in winter) but not in TX or in CA.
9. The size of a ding in a gun's finish doesn't matter, what matters is whether it’s a safe ding or not.
10. 1 in a row is a trend, 2 in a row is statistically significant, and 3 in a row is an irrefutable fact.
11. Never buy a WSM or RCM cartridge for a safari rifle or your go to rifle in the USA because if they lose your ammo you can't find replacement ammo but don't worry 280 Rem, 338-06, 35 Whelen, and all Weatherby cartridges abound in Africa and back country stores.
12. A well hit animal can run 75 yds. in the open and suddenly drop with no initial blood trail, but the one I shot from 200 yds. away that ran 10 yds. and disappeared into a thicket and was not found was lost because the bullet penciled thru. I am 100% certain of this even though I have no physical evidence.
13. A 300 Win Mag is a 500 yard elk cartridge but a 308 Win is not a 300 yard elk cartridge even though the same bullet is travelling at the same velocity at those respective distances.
 
Posts: 10181 | Location: Loving retirement in Boise, ID | Registered: 16 December 2003Reply With Quote
One of Us
posted Hide Post
Well, I dared to dream. Thank you guys for your input.
 
Posts: 54 | Location: Newport, WA-Susanville, CA | Registered: 04 September 2008Reply With Quote
  Powered by Social Strata  
 


Copyright December 1997-2023 Accuratereloading.com


Visit our on-line store for AR Memorabilia