THE ACCURATERELOADING.COM MILITARY FORUM

Go
New
Find
Notify
Tools
Reply
  
M98K Marked "byf"
 Login/Join
 
one of us
Picture of wildcat junkie
posted
Anybody know anything about a M98k marked thus?

It has byf stamped on the receiver, the trigger gaurd and floorplate.

Except for the stamped bottom metal the fit and finish of the metal is pretty good.

The bore is very good with no apparent throat erosion. It does need a crown job though.
 
Posts: 2440 | Location: Northern New York, WAY NORTH | Registered: 04 March 2001Reply With Quote
One of Us
posted Hide Post
Hi!
means made by Mauser, probably end of 1942 or 1943 with your description.
 
Posts: 157610 | Location: Ukraine, Europe. | Registered: 12 October 2002Reply With Quote
One of Us
posted Hide Post
According to an article by Ludwig Olsen in "Mauser Rifles" (an NRA Reprint) "byf" is the mfg. code for Mauser-Werke, A.-G., Oberndorf a./N. That means it's an Oberndorf Mauser.
 
Posts: 8169 | Location: humboldt | Registered: 10 April 2002Reply With Quote
one of us
posted Hide Post
I have one 1944 marked byf. According to "Backbone of Wehrmacht", byf is Oberndorf.

[ 04-25-2003, 13:11: Message edited by: Pyrotek ]
 
Posts: 638 | Location: O Canada! | Registered: 21 December 2001Reply With Quote
one of us
Picture of wildcat junkie
posted Hide Post
quote:
Originally posted by Pyrotek:
I have one 1944 marked byf. According to "Backbone of Wehrmacht", byf is Oberndorf.

This one is also "44".

Other than the crappy bottom metal it looks pretty well made.

I picked it up in a nice Walnut sporter stock for $150. It needs a crown job, but the bore is near excellent. The bolt # doesnt match, but there is no play when closed on an empty case when the firing pin is down on an empty primer pocket. The rear sight is gone and the the sight section has been "blended in. The front sight dovetail has been opened up to 3/8" for a williams bead and a receiver sight has been installed. It obviously no longer has any "collector" value.

What is the metalurgy like on these? I tried to scribe a line on the receiver ring and it seemed pretty hard.

Would this be a good one to rechamber to 8X68S?
 
Posts: 2440 | Location: Northern New York, WAY NORTH | Registered: 04 March 2001Reply With Quote
one of us
Picture of D Humbarger
posted Hide Post
WJ if you do not want that stamped trigger guard floor plate & probably a stamped follower too i would like to buy them from you.

[ 04-26-2003, 17:10: Message edited by: D Humbarger ]
 
Posts: 8355 | Location: Jennings Louisiana, Arkansas by way of Alabama by way of South Carloina by way of County Antrim Irland by way of Lanarkshire Scotland. | Registered: 02 November 2001Reply With Quote
one of us
posted Hide Post
wildcat junkie,

My 1944 byf also have a crappy exterior and mirror-like bore. My smith said this gun has the best bore in a Mauser he's ever seen. He also said near the end of WW2 the German make guns with pretty much anything steel they can find. It will make me happier to think the steel of my gun comes from a "Panzer", not from a manhole cover.

Assuming your rifle is just like mine then the steel can be very good steel still. It's fine for rebarrelling, it will work, but don't try to polish it and reblue it. Sandblasting and fine parkerizing will do well for the kind of surface on our rifle as these surface treatments will help hide imperfections. I also have a 1933 non-Nazi Mauser that is opposite of my 1944 Mauser : It has glass-like exterior and a wash-out barrel. That's the kind of gun I wouldn't hesitate to put a new barrel on.

Pyrotek
 
Posts: 638 | Location: O Canada! | Registered: 21 December 2001Reply With Quote
One of Us
posted Hide Post
Hi , not true about steel quality . machining and finishing were awful but there was no compromise on steel quality until the end.
 
Posts: 157610 | Location: Ukraine, Europe. | Registered: 12 October 2002Reply With Quote
one of us
Picture of wildcat junkie
posted Hide Post
quote:
Originally posted by Edmond:
Hi , not true about steel quality . machining and finishing were awful but there was no compromise on steel quality until the end.

Actually the exterior is very nice, although it has already been reblued @ some point.

The machining looks as good as any M98K I have seen.

Maybe the "Fuerer" was inspecting that day. [Big Grin] [Big Grin]

Pyrotek:

Actualy I plan to use the issue barrel (rechambered to 8X68S) as the bore is in near excellent condition with little or no throat errosion. The rifling looks sharp, but there is some slight rust, no pitting. It definately needs a crown job though as it looks as though somebody dropped it straight down on a "Panzer" or something. One side is slightly musroomed @ the O. D.

[ 04-29-2003, 01:39: Message edited by: wildcat junkie ]
 
Posts: 2440 | Location: Northern New York, WAY NORTH | Registered: 04 March 2001Reply With Quote
one of us
posted Hide Post
quote:
Hi , not true about steel quality . machining and finishing were awful but there was no compromise on steel quality until the end.
quote:
From: France, Paris area
Well, of course you know better, Nazi occupied Paris and you get a better, closer look [Big Grin]
 
Posts: 638 | Location: O Canada! | Registered: 21 December 2001Reply With Quote
one of us
Picture of wildcat junkie
posted Hide Post
quote:
Originally posted by D Humbarger:
WJ if you do not want that stamped trigger guard floor plate & probably a stamped follower too i would like to buy them from you.

D.Humbarger: Check your e-mail
 
Posts: 2440 | Location: Northern New York, WAY NORTH | Registered: 04 March 2001Reply With Quote
one of us
Picture of The Dane
posted Hide Post
http://users.swing.be/sw017995/k98kmarkings.htm
his should solve any problems dating Mausers!
 
Posts: 1102 | Location: Denmark | Registered: 15 October 2001Reply With Quote
  Powered by Social Strata  
 


Copyright December 1997-2025 Accuratereloading.com


Visit our on-line store for AR Memorabilia

 

image linking to 100 Top Hunting Sites