9.3x64 Brenneke spread to 416?

01 January 2016, 21:23

jeffeosso

not that I am aware of --

as you can make x64 cases from turning down HH cases, the results would be very close to a 400HH -- not exactly a 416 rem, due to taper and capacity -

so, it would be an easy rework a 3006 or 7 rem mag to this config, a bit of work to make reamers, dies, and brass, and wind up with a 416 that has been matched ...

sort of like turning the belt off a 416 rem, so to speak

opinions vary band of bubbas and STC hunting Club

Words aren't Murder - Political assassination is MURDER
Information on Ammoguide about
the416AR, 458AR, 470AR, 500AR
What is an AR round? Case Drawings 416-458-470AR and 500AR.
476AR,
http://www.weaponsmith.com

01 January 2016, 22:48

drewhenrytnt

A chap on another forum asked about it and I recommended he ask here. Said he had no desire, so I asked.

Thanks for the info gents. I'll pass it along.

Andy B

02 January 2016, 03:46

Big Wonderful Wyoming

quote:
Originally posted by jeffeosso:
not that I am aware of --

as you can make x64 cases from turning down HH cases, the results would be very close to a 400HH -- not exactly a 416 rem, due to taper and capacity -

so, it would be an easy rework a 3006 or 7 rem mag to this config, a bit of work to make reamers, dies, and brass, and wind up with a 416 that has been matched ...

sort of like turning the belt off a 416 rem, so to speak

Yes until you get to Fairbanks or Windhoek with no ammo.

02 January 2016, 05:32

jeffeosso

quote:
Originally posted by Big Wonderful Wyoming:
Yes until you get to Fairbanks or Windhoek with no ammo.

that's more or less entirely irrelevant in the WILDCAT forum...

You know, where we discuss wildcats -- not where we discuss piss poor planning for a trip. btw, i do firmly believe that EVERY case of gun-but-no-ammo could have been avoided by better planning

my 416 AccRel is obviated by the 416 ruger - that's cool ... in fact, somewhat complementary .. this case, as presented, wouldn't make a ruger equal -- it would make about a 400hh

9,3x64 is smaller a than 375hh which is smaller than a 416 rem which is smaller than a 416 ruger, which is smaller than a 416 Accrel ....

without bothering to do the math, its going to be larger than a 416 taylor, and smaller than a 416 remington ...

02 January 2016, 06:10

.366torque

boomie asked me to neck up a x64 case to 416. Wasn't much of a shoulder.

quote:
Originally posted by jeffeosso:
quote:
Originally posted by Big Wonderful Wyoming:
Yes until you get to Fairbanks or Windhoek with no ammo.

that's more or less entirely irrelevant in the WILDCAT forum...

You know, where we discuss wildcats -- not where we discuss piss poor planning for a trip. btw, i do firmly believe that EVERY case of gun-but-no-ammo could have been avoided by better planning

my 416 AccRel is obviated by the 416 ruger - that's cool ... in fact, somewhat complementary .. this case, as presented, wouldn't make a ruger equal -- it would make about a 400hh

9,3x64 is smaller a than 375hh which is smaller than a 416 rem which is smaller than a 416 ruger, which is smaller than a 416 Accrel ....

without bothering to do the math, its going to be larger than a 416 taylor, and smaller than a 416 remington ...

02 January 2016, 17:09

jeffeosso

yep .. i wouldn't expect much, unimproved - which is why i think it would be more or less about a 400 hh ---

its early!

02 January 2016, 22:53

MickinColo

05 January 2016, 10:04

drewhenrytnt

The chap that asked about it lives in Sweden and RUM brass is apparently non-existent. Says he has shit piles of Brenneke brass and was curious about doing such.

Andy B

05 January 2016, 16:11

jeffeosso

then he'd have something nifty -- and it would smack a mosse

can he get 404 brass? you can make my carts from 404 brass