The Accurate Reloading Forums
HELP : .375 Barrel diameter
17 January 2005, 22:51
BwanamichHELP : .375 Barrel diameter
Could anyone let me know the barrel diameter of a .375?
Thanks,
Happy hunting!
"...Them, they were Giants!"
J.A. Hunter describing the early explorers and settlers of East Africa
hunting is not about the killing but about the chase of the hunt.... Ortega Y Gasset
18 January 2005, 01:22
AllenBoselyHey Bwananich, I know they can vary quite a bit, but if it helps I had my Pac-nor barrel at 24" .275 dia. I measured a cuple of wimchester
Safri Express they ran from .290 to .320 hope that helps. allen PS Dakota I belive is .650 usually.
It's a Mauser thing, you wouldn't understand.
18 January 2005, 01:53
Willhuh?
-------------------------------
Will / Once you've been amongst them, there is no such thing as too much gun.
---------------------------------------
and, God Bless John Wayne. NRA Benefactor, GOA, NAGR
_________________________
"Elephant and Elephant Guns" $99 shipped.
“Hunting Africa's Dangerous Game" $20 shipped.
red.dirt.elephant@gmail.com
_________________________
If anything be of note, let it be he was once an elephant hunter, hoping to wind up where elephant hunters go.
18 January 2005, 02:18
Bwanamichquote:
Originally posted by AllenBosely:
Hey Bwananich, I know they can vary quite a bit, but if it helps I had my Pac-nor barrel at 24" .275 dia. I measured a cuple of wimchester
Safri Express they ran from .290 to .320 hope that helps. allen PS Dakota I belive is .650 usually.
Thanks Allen,
I have a Safari Express and I am trying to get a NECG rear sight through their online store and they ask to specify the barrel diameter. I don't have my rifle with so can't measure. The barrel diameter options for the sight I want on their site start at .600/.675 and upwards.

"...Them, they were Giants!"
J.A. Hunter describing the early explorers and settlers of East Africa
hunting is not about the killing but about the chase of the hunt.... Ortega Y Gasset
18 January 2005, 03:02
mhoquote:
Originally posted by Bwanamich:
Could anyone let me know the barrel diameter of a .375?
Thanks,
Happy hunting!
Oh man, they come with all sorts of muzzle diameters. Typical barrel contours put on .375 H&H are #4 or #5, but some factory barrels are considerably heavier than that - Steyr springs to mind. If you are ordering a front sight for an existing barrel, though, and the diameter has to be specified within a pretty limited interval, I think it would be rather "brave" of you if you ordered based on what other peoples' barrels measure.
- mike
*********************
The rifle is a noble weapon... It entices its bearer into primeval forests, into mountains and deserts untenanted by man. - Horace Kephart
18 January 2005, 05:01
vapodogdo this
1 decide where on the barrel you want to mount the rear sight.....and mark it with a piece of electrical tape.
2 find a caliper...digital, vernier. or dial and measure the barrel diameter there.
3 give that number to NECG.
///////////////////////////////////////////////////////////////////////////
"Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery."
Winston Churchill
18 January 2005, 05:19
fredj338You are just going to have to neasure it. Maybe, MAYBE, someone elses M70 will have a bbl. close enough that they can provide your measurement. It will be over .700", I'll bet on that.
LIFE IS NOT A SPECTATOR'S SPORT!
18 January 2005, 08:46
AllenBoselyYeah, Bwanamich you really should mesure your barrel on two of the Safari Express one was .690 and one was .317 both were current made guns both at Sportsman warehouse about a month ago. allen
It's a Mauser thing, you wouldn't understand.
18 January 2005, 19:38
BwanamichThanks to all. I will wait till i get back home and measure.
"...Them, they were Giants!"
J.A. Hunter describing the early explorers and settlers of East Africa
hunting is not about the killing but about the chase of the hunt.... Ortega Y Gasset