Had a bit of a range session with my new Steyr Safety-Bolt Hunter .376 yesterday, and really liked it. Haven't seen anything on here about that model...so have I said a dirty word in mentioning it? Or maybe I was just asleep....
Tried both Hornady loads in it, the 225 gr. spire point Interlock, and the 270 gr. Interlock. As it came from the factory, its iron sights were dead on at 200 meters. On well enough to hit clay pigeons on our range's sand berm shooting offhand with the 225 Hornady stuff, anyway.
Don't have a scope on it yet, as my rings & bases have been back-ordered. When they arrive, will be putting on something in about a 1.5x5 variable.
Bought a case (300 rounds) of Hornady brass from Graf's, and plan to use mainly Barnes-X bullets for serious stuff, along with a variety of my own cast slugs for plinking.
Has anyone out there done any reloading for it that they'd like to share info about?
Any comments on the rifle itself? Mine slicked up considerably with a few hundred cranks of the bolt handle and discerning application of a product similar to dri-slide....
Appreciate any comments you folks have...
AC
[ 09-30-2003, 04:24: Message edited by: Alberta Canuck ]
Posts: 9685 | Location: Cave Creek 85331, USA | Registered: 17 August 2001
CDNN had the ammo cheap and I bought enough to last the rest of my life. I'm impressed with the rifles' accuracy but it gets heavy and the balance is funny with a European scope on it. I'm going to have to find a light 2-6x33.etc. I does kick a bit with 270 loads and I'm not recoil shy. I'd say more than my 375 H&H and sharper than a 416. I'm looking forward to using it for something after I bought it. The close out price was too good to pass up.
Posts: 1275 | Location: Fla | Registered: 16 March 2001
A handfull of AR folks have these rifles and we all like 'em just fine. If you do a "search" you will find plenty of info and some pet loads. I have a Leup 1.75 x 6 Vari-X III in Leup dual dovetail mounts on mine, and think it's a pretty good match. I wound up useing high rings to deal with a bolt clearance issue, so keep an eye out for that potential problem when choosing scope and mounts.
Elmo
Posts: 586 | Location: paloma,ca | Registered: 20 February 2002
Particular thanks to Elmo for the "heads up" on the scope clearance. Was sitting here working the bolt some more on mine last night, and wondered if that "crank" in the bolt handle might be a little high for a lot of scope eyepieces to clear.
Actually, that surprises me a bit, for the handle on my Steyr '69 brown-stock SSG .308 Match clears all scopes pretty easily, as does the handle on my Steyr Professional 8x57. This one seems to be a bit retrograde in that the handle does appear to lift higher than those on the earlier models.
Thanks again, y'all... AC
[ 10-01-2003, 09:15: Message edited by: Alberta Canuck ]
Posts: 9685 | Location: Cave Creek 85331, USA | Registered: 17 August 2001
quote:Originally posted by tigertate: I like mine too but I cannot get down on the iron sights with the prohunter stock. Anyone else have this problem?
Some people have to cheat forward on the stock to do so. I would consider them as emergency backup and rely on a scope as a standard sighting system.
Posts: 1079 | Location: San Francisco Bay Area | Registered: 26 May 2002
Slingster: Thanks, I thought it was just me. By the way, I have a Ching Sling on my 416 Reimngton; great idea. The stock is a Clifton. Do you know what happent to him?
Posts: 11143 | Location: Texas, USA | Registered: 22 September 2003
I keep hearing rumors of Brent Clifton's location, but so far I've not been able to contact him. I don't think he's in the gun business anymore.
Thanks for the kind words about the Ching Sling. On that .416 you should try my new Safari Ching Sling: twice as wide for more carrying comfort and just as steady.
Posts: 1079 | Location: San Francisco Bay Area | Registered: 26 May 2002
Slingster: Who has 'em in the Houston area or do sell by mail? I got my first one from Brent when he built my stock right about the time he moved to Medina, TX.
Posts: 11143 | Location: Texas, USA | Registered: 22 September 2003
Tigertate, I have the same problem with the stock. Was looking at rebuilding the gun but some advice on the gunsmith forum put it in the "too hard to do" category. The only thing I did that helped was add a couple spacers and ride forward on the stock. I have a ghost ring in the rear scope base and it works but the sight picture is not quite right. For what it's worth. The gun though is a nice shooter and will flatten big pigs and such from any angle. HunterJim used it in Africa with success. It's a keeper. Jeff
I like mine too... I hunt & occasionally guide on a game ranch and bought mine to have something compact to follow a hit Gemsbock or Eland into the scrub-oaks. I was hoping to dismount my scope for the dark brush and use the iron sights but it appears not to be. Still, its a great gun otherwise. If I get to go Africa it will go, too.
Posts: 11143 | Location: Texas, USA | Registered: 22 September 2003
quote:Originally posted by tigertate: Slingster: Who has 'em in the Houston area or do sell by mail? I got my first one from Brent when he built my stock right about the time he moved to Medina, TX.
You could mail order from Galco directly or get a referral from them to a local distributor in your area: www.usgalco.com
Posts: 1079 | Location: San Francisco Bay Area | Registered: 26 May 2002
Thanks, Slingster. HunterJim: I've read and enjoyed both 376 articles and they are still online. I've also followed a lot of the other threads with interest but posted this before I saw anything on stocks. Dogworker, Lone Wolf Stocks says he can do the 376 ProHunter in his Stalker line. Much better for iron sights but I forgot to ask him how he was going to handle the trigger guard. I have some of his work and it is first class.
Posts: 11143 | Location: Texas, USA | Registered: 22 September 2003