THE ACCURATERELOADING.COM MEDIUM BORE RIFLE FORUM


Moderators: Paul H
Go
New
Find
Notify
Tools
Reply
  
Husqvarna 9.3 ?
 Login/Join
 
one of us
Picture of Muletrain
posted
The stamp on the barrel was just 9.3 so which one is it most likely to be?

This is a Husqvarna on a 98 Mauser action with a very light weight sporter stock. It has a one leaf rear sight with a very shallow v and a barrel band swivel. The grip is rounded and checkered with no cap. Is this a 9.3 x 57, and if so how hard is it to find ammo for this rifle?


Elephant Hunter,
Double Rifle Shooter Society,
NRA Lifetime Member,
Ten Safaris, in RSA, Namibia, Zimbabwe

 
Posts: 955 | Location: Houston, Texas, USA | Registered: 13 February 2002Reply With Quote
one of us
Picture of boha
posted Hide Post
I have two in front of me and they are both x62.
Try feeding it something.
Boha
 
Posts: 493 | Location: Finland | Registered: 18 July 2001Reply With Quote
One of Us
posted Hide Post
Most Husquarnas stamped 9.3 is cal 9.3x57
the 9.3x62 is in all the cases i have seen stamped 9.3x62 (a few hundreds)
It is easy to check even you dont have the right ammo. If you have a empty 30.06 case and it can be chambered it is definitly a 9.3x62 if it stops about 1/4" before closed it is most likely a 9.3x57
 
Posts: 571 | Registered: 16 June 2005Reply With Quote
one of us
Picture of sbhva
posted Hide Post
quote:
Originally posted by Muletrain:
The stamp on the barrel was just 9.3 so which one is it most likely to be?

This is a Husqvarna on a 98 Mauser action with a very light weight sporter stock. It has a one leaf rear sight with a very shallow v and a barrel band swivel. The grip is rounded and checkered with no cap. Is this a 9.3 x 57, and if so how hard is it to find ammo for this rifle?


I should be able to tell which 9.3 your Husqvarna is chambered in from the serial number.


Steve
 
Posts: 120 | Location: Wisconsin, USA | Registered: 05 February 2004Reply With Quote
one of us
posted Hide Post
Probably a m96 action too.
 
Posts: 4821 | Location: Idaho/North Mex. | Registered: 12 June 2002Reply With Quote
One of Us
posted Hide Post
It sounds like a '96 stock to me too.
Does the action cock on closing or on opening?
If on closing it's a '96 if on opening it's a '98.
It realy won't matter which action it is in term of use or reliability they are both good actions.
The '96 were made by Husqvarna, the '98 by FN, both are excellant.
I don't know how difficult it is to find loaded ammunotion in the US of A. It is still made by Norma and cases for reloading are still sold.
Dies are made by Hornady and 8x57 cases can be resized with ease.
You have a good short to medium range rifle, they are great to shoot, and kill very well
 
Posts: 1374 | Location: New Zealand | Registered: 10 February 2005Reply With Quote
One of Us
posted Hide Post
Howdy
If the rifle is a 96 action, it is a 9.3x57mm.
Both calibers were made in the FN action, however ther were two pre world war II models, M-46 and M-146.

The model M-46 was made from 1927-1937, most in 9.3x57mm (WALNUT STOCK), beginning at s/n 500 for approximately 15,000 guns. (Some were 6.5x55mm) (Swedish M-96 action) (None in 9.3x62mm)
The model M-146 was made on FN M98 Belgian actions with clip slot and thumb cut (Beech stock), again, most in 9.3x57mm, beginning at s/n 20,000 for approximately 12,000 guns. Some are 9.3x62, some in 6.5x55mm.
Husqvarna ran out of FN actions and reverted to the Swedish M-96 action in 1941. Approximately 8000 were made during WWII for civilian use. (Most 9.3x57mm) Some, maybe 3000 were made in 6.5x55mm. The WWII s/n started at 40,000 for the 9.3x57mm and 70,000 for the 6.5x55mm.
Production continued after WWII with a mix of Swedish M-96 and new FN M-98 actions Chambered for 6.5x55mm, 8x57mm, 9.3x57mm and 9.3x62mm.

LLS


 
Posts: 996 | Location: Texas | Registered: 14 October 2004Reply With Quote
one of us
posted Hide Post
It can either one if its a mod. 98 Mauser Husky as they came in both calibers....

The easiest way to tell is try a 9.3x62 in the chamber, if its a 9.3x57 the 62 case will not chamber, but also try a 9.3x64 to be sure no one has been tinkering with it....

Actually a gunsmith chamber cast is the safe way to determine the caliber....


Ray Atkinson
Atkinson Hunting Adventures
10 Ward Lane,
Filer, Idaho, 83328
208-731-4120

rayatkinsonhunting@gmail.com
 
Posts: 42320 | Location: Twin Falls, Idaho | Registered: 04 June 2000Reply With Quote
one of us
Picture of tiggertate
posted Hide Post
Actually, it was years after the 93. x 57 that the 9.3 x 62 became a factory offering. During that period they stamped the barrels "9.3" only without any length indicated. So any barrel marked only "9.3" left the factory as a 9.3 x 57 (as that was the only caliber produced during those years) BUT..

many were rechambered later to x 62 so you really need to do as Ray and others said to be sure.


"Experience" is the only class you take where the exam comes before the lesson.
 
Posts: 11143 | Location: Texas, USA | Registered: 22 September 2003Reply With Quote
One of Us
posted Hide Post
Ray,
Very sensible advice on checking the chamber. Will a x57 or x62 extractor fit over a x64 rim? I have no idea, I just know that it has a larger than the other two.

Sierra,
Not all 146 rifles were made with Beech stocks, mine is Walnut.
 
Posts: 1374 | Location: New Zealand | Registered: 10 February 2005Reply With Quote
one of us
Picture of Fritz Kraut
posted Hide Post
All Husqvarna rifles marked "9,3 m.m." left the factory as 9.3x57, as did all "8 m.m." leave as 8x57. Ray's advicing to measure with a 9.3x62 catridge is wise as there have always been tinkerers who love to ream up the good old 9.3x57. However, it is as good as it is.

Here is a fine article of the Husqvarna 9.3 mm Mauser: http://www.pettsons.net/m46.html

Regards,

Fritz


The true and only Fritz Kraut
 
Posts: 846 | Location: Sweden | Registered: 19 April 2001Reply With Quote
  Powered by Social Strata  
 


Copyright December 1997-2023 Accuratereloading.com


Visit our on-line store for AR Memorabilia