Hello,
Purchasing subject rifle(cal.30-06) and curious as to any feedback on the Hawkeye version of the Mod.77 Ruger. Been hearing the new designed trigger is not as good as the previous ones. Not expecting a match grade trigger, but would hope it would break at something near 3lbs. Travel or creep not a problem, predictable let off is good for me. Thanks,

martin

there is nothing wrong with the trigger on the hawykeye.
i think it is over 3 lbs but i don't have any complaints about mine, i like it better than the trigger on my mdl 700.

My Hawkeye is My only (small/medium bore) rifle that still has the stock trigger on it. Lets off at 2 3/4 lbs. with no creep

If you don't like the trigger on a hawkeye . I recomend you givw a call to wolf gun springs.
They make a replacment spring that will bring your pull weight down a fair amount and I only takes about 10 minites to install.
I think the spring costs about 3.50
Let us know how yours shoots...tj3006

Hello,
Thanks for the feedback, sounds all positive.
I did purchase some year or so ago an RSI, 308, not the Hawkeye version, and for a factory rifle, it is fitted/finished as good as any I have seen. I normally slick up the bolt on new rilfes, but none required for it is smooth as any of my M98's which have had lots of work done on them. Truth of the matter, the trigger on current one is very good and if the new one is as good, no complaints from me. Should have the Hawkeye this week and by next weekend will send rounds down range. Again, thanks.

martin

Martin, I've had an 18.5" barreled 30-06. Forget it and go with the 308 (have had a 77 RSI in 308 as well). The 30-06 is just too much of a good thing with a barrel that short IME.

I have a pre hawkeye version of the RSI in .308 that has the new trigger. It lets go a about 4.5 lbs and is very crisp. It's not benchrest quality but certainly acceptable. The new triggers can be determined by looking at the back of the trigger. If it has a groove running its length it's the new one.

I agree with the comments about .308 vs .30-06 in a short carbine. The velocity advantage won't be there with the short barrel , so why not save weight with the shorter action?

BTW I love this rifle. Handy as can be and the front sling swivel nearer the muzzle makes it carry well.

I have an NECG peep sight on it I like so much I haven't mounted a scope yet.

Hello Citori,
Thanks for the tip about the groove on the backside of the trigger. Sure enough it is there and for me the trigger is very good for a hunting rifle. I agree that the short barrel version in '06 is a bit much, but just wanted the current RSI 308 I have to not be lonely.
My 308 RSI has a steel bottom metal and in checking w/ the factory, they told me that the normal ones were of aluminum/alloy?? I have the NECG peep on mine as well, but removed the barrel mtd. rear sight so as to not interfere w/ sight picture. I understand the Hawkeye's have steel bottoms as normal w/ some "fancy" engraving. Once I get the '06 will pack off the bottom metal of each and send to Mr. Turnbull for his color casehardening magic. Have already done the scope rings and after I recover from the bottom metal will send him the bolt shrouds of each. Did replace the plastic grip cap w/ steel one from Ruger, not expensive, and will do the same w/ the new one. Mr. Turnbull's firm has done the same work on my RSM/375H&H and from my point of veiw helps add a bit of class to the rifles. He does first class work. Again, thanks for the tip.

martin

Didn't know Ruger offered a metal grip cap. Tell me more about Turnbull. I may have to spend some money.

I'll check my bottom metal tonight. Maybe I have steel as well.

Hello Citori,
Go to Ruger Parts Dep't and ask for steel grip cap which is std. on the RSM's. Believe it is less than 10 bucks if I remember correctly. The diameter is a bit on the large size, but some file work will bring it down to correct size. Has center wood screw for attachment and if desired can even buy the replacement Ruger logo insert to cover screw head. I didn't do that, just cold blued slotted steel wood screw.
Turnbull Restorations is the firm and a search for same will bring his firm up. If interested give them a call and discuss what you are wanting done and if you do some of the initial polishing, they will work with you on pricing a bit. Saves them some labor and they are good folks. Should warn you that once on their web site and see their work, you will be wanting to send lots of stuff to them!!