THE ACCURATERELOADING.COM MEDIUM BORE RIFLE FORUM


Moderators: Paul H
Go
New
Find
Notify
Tools
Reply
  
Laminated stock
 Login/Join
 
<monz>
posted
where can I buy a Laminated stock for a Remington 700 BDL?
 
Reply With Quote
one of us
posted Hide Post
Fajen stocks in Missouri, I don't have the address but I believe Midway Shooters Supply purchased them. I have a couple and they are very good quality.

Good Hunting, "Z"
 
Posts: 352 | Location: Grand Island, NE. USA | Registered: 26 January 2001Reply With Quote
one of us
posted Hide Post
Boyd's Gunstocks also have very good laminated stocks for the 700. They are located in Mitchell, South Dakota and their web site is www.boydboys.com. I have a couple of their laminated stocks and have been very pleased with them. I have one on order now.

Tom
 
Posts: 48 | Location: Sierra Vista, AZ | Registered: 24 August 2002Reply With Quote
one of us
posted Hide Post
Noticed that you are from Sweden. Boberg in Orrholen NV of Falun sells laminated stocks of a very good quality.
 
Posts: 544 | Location: Sweden | Registered: 27 October 2001Reply With Quote
<monz>
posted
Tsquare: Are the Boyd�s stocks fully finished or do yuo have to do som finish work yourself?
Inside, outside, recoilpad?
 
Reply With Quote
<monz>
posted
Wachtel: Han s�ljer v�l bara grovfr�sta stockar?
Jag har gjort ett par kolvar tidigare av hans grovfr�sta �mnen, men vill nu ha en f�rdig stock.
Mvh M�ns
 
Reply With Quote
one of us
posted Hide Post
Dear Monz,

I'm reasonably certain that Boyd's offers both fully finished "drop-in" stocks as well as a mostly finished stock. You could check the web site and it will tell you what all they have available.

Tom
 
Posts: 48 | Location: Sierra Vista, AZ | Registered: 24 August 2002Reply With Quote
one of us
posted Hide Post
You can buy a Remington factory laminated stock directly from Remington. Current prices run between $241 to $247 plus shipping.

This is the link to the Remington on-line parts catalog for Model 700's. You will need Adobe Acrobat reader. Scroll down to page 4 of the print file and start looking for STK ASSEM and either LAM or LAMINATE.

http://www.remington.com/pdfs/m700parts.pdf

This is the link to the main Support page:
http://www.remington.com/support/support.htm

From there you can find the customer service telephone number or email them.
 
Posts: 1027 | Registered: 24 November 2000Reply With Quote
one of us
posted Hide Post
boyds are $116 for finished and much less for the unfinished. For an additional $20, you can have them install the swivel studs, and include a "super-sling" with it.

They are ready for bolt-in when the arrive (finished) and come is several configurations as well as colors.

I have one on order as well. (JRS Classic)
 
Posts: 1496 | Location: behind the crosshairs | Registered: 01 August 2002Reply With Quote
one of us
Picture of dogcatcher223
posted Hide Post
Does anyone have a Boyds? I just wondered if it is a true drop-in stock? I want one, but not if i have to sand and bed the thing just to get it to work. I guess my main concern is i wouldn't want my accuracy to drop just because i got a new stock that was not fit exactly perfect like a factory.
 
Posts: 525 | Registered: 21 December 2002Reply With Quote
one of us
posted Hide Post
My gunsmith told me there may be a slight bit of removal, but nothing that a novice can't do. He told me they are soo much stronger than the standard wood stock, that they are almost like installing pillars in the original stock. He seemed to be impressed with them. I got the feeling it would be a no-brainer. Boyds told me that a magnum would require a "little" fitting, but the standard LA would go in nice and tight right from the jump. HTH
 
Posts: 1496 | Location: behind the crosshairs | Registered: 01 August 2002Reply With Quote
one of us
posted Hide Post
One of our better local gunsmiths is nuts about Boyds stocks. He's been putting them on his own rifles and on customers rifles like crazy for the past couple of years. They can be just bolted on, but he does such an awesome glass bedding job that people are having him install them. They look good, fit most folks real well, and, at least when he's done with them, the rifles shoot great too. Regards, Guy
 
Posts: 327 | Location: Washington State, USA | Registered: 18 July 2002Reply With Quote
one of us
posted Hide Post
The inletting of the unfinished Boyds JRS's I have used were nice snug drop in. However, I still glass bed them. I buy the unfinished ones because the JRS is too clubby for my tastes. The unfinished ones are drop-in inletted but need final sanding and finishing to complete. I shorten and slim down the forend, open up the pistol grip, reshape the cheekpiece to the English pancake style, lower the comb a bit, hollow out the butt, install a Decelerator pad, final sand and finish. It ends up weighing around 30 oz and fits me perfectly.
 
Posts: 354 | Location: Texas, USA | Registered: 11 February 2001Reply With Quote
one of us
posted Hide Post
quote:
Originally posted by m700:
They can be just bolted on, but he does such an awesome glass bedding job that people are having him install them.

m700,

How does he bed them -- full-length, free floated or with forend tip pressure? Does he do the whole receiver, and how about the bottom metal?

I have one arriving Monday for a Ruger 77 so inquiring minds want to know.

John
 
Posts: 1246 | Location: Northern Virginia, USA | Registered: 02 June 2001Reply With Quote
one of us
posted Hide Post
quote:
Originally posted by Ed:
I shorten and slim down the forend, open up the pistol grip, reshape the cheekpiece to the English pancake style, lower the comb a bit, hollow out the butt, install a Decelerator pad, final sand and finish. It ends up weighing around 30 oz and fits me perfectly.

Ed,

Can you post a picture? I am planning on doing much the same.

What is your preferred finish?

John
 
Posts: 1246 | Location: Northern Virginia, USA | Registered: 02 June 2001Reply With Quote
one of us
posted Hide Post
Sorry, I am still in the stone age regarding photos and posting... I finish all of my stocks (laminated as well as solid) with Chem-Pak Pro-Custom Oil. See attached.

http://www.brownells.com/aspx/NS/store/ProductDetail.aspx?p=5531
 
Posts: 354 | Location: Texas, USA | Registered: 11 February 2001Reply With Quote
one of us
posted Hide Post
quote:
Originally posted by Ed:
Sorry, I am still in the stone age regarding photos and posting...

E-mail would also be fine, it's in my user profile -- not a huge rush, my stock isn't getting here until Monday. [Smile]

John
 
Posts: 1246 | Location: Northern Virginia, USA | Registered: 02 June 2001Reply With Quote
one of us
posted Hide Post
Another vote for the Boyd's stocks. I bought a JRS Classic Laminate for a 338 WM Savage and the fit was nearly perfect out of the box (excepting hogging out the barrel channel of course) and it looks great--I glassed it and it shoots wonderfully. Cheap too. FWIW
 
Posts: 767 | Location: Seeley Lake Montana | Registered: 17 April 2002Reply With Quote
  Powered by Social Strata  
 


Copyright December 1997-2023 Accuratereloading.com


Visit our on-line store for AR Memorabilia