Go | New | Find | Notify | Tools | Reply |
one of us |
since ive bought two and both were for pre war m-70s.close but no ceegar''so send me a text or email of the underside of the rear ring and i will buy the correct one; this is for a 300 H&H and 375 H&H 'the ccorrect one is smoogth the other has a thin dovetail a a flat and a raised flat serfice in the middle for a pre war gun, dont need the pre war base Its amazing how many don't know this.. Ray Atkinson Atkinson Hunting Adventures 10 Ward Lane, Filer, Idaho, 83328 208-731-4120 rayatkinsonhunting@gmail.com | ||
|
One of Us |
I will check, as I have quite a few bases, but not sure about magnums. Stay tuned. | |||
|
One of Us |
Ray, the Redfield base you need is number 511114, it will be stamped 70-AM, but you probably know all that. It appears that the dovetail on the pre war base could be milled off and it would then fit a post war receiver?? In my clutter I did find a set of Talley Lights(Low) for H&H spacing. | |||
|
one of us |
Ray, I sent you and email with pictures. Remember, forgivness is easier to get than permission. | |||
|
one of us |
Terry, wrong bases, both of Yours are modified standard 06 ..You have a PM Ray Atkinson Atkinson Hunting Adventures 10 Ward Lane, Filer, Idaho, 83328 208-731-4120 rayatkinsonhunting@gmail.com | |||
|
one of us |
Still looking...everyone has the wrong base,,ether std 70 06 length or pre war mg.!! Neither of which will work.. Ray Atkinson Atkinson Hunting Adventures 10 Ward Lane, Filer, Idaho, 83328 208-731-4120 rayatkinsonhunting@gmail.com | |||
|
One of Us |
Ray, Check these guys out https://www.vintagegunscopes.com/redfield-bases | |||
|
One of Us |
Ray, I've got an extra. It was on one of my mid-50s 300 H&Hs. Relatively clean but one of the side hold down bolts is a replacement newer kind that does not have a screw slot. Suspect you can replace that easily enough. It's stamped 70 A MAG but is identical to two others I have that are stamped 70 AM. $40 shipped. If interested pls PM address and I may can get it in the mail tonight... Good hunting | |||
|
One of Us |
Ray, PM sent. | |||
|
One of Us |
Ray, I haven't heard yes, no or maybe regarding my offer. Likewise regarding your earlier request 2-3 weeks ago where I offered to give you a correct base without mounting screws and side bolts, or sell to you for $50 an unused complete 51114 mount still in the box that I bought from Randy Shuman about 40 years ago. I'm certainly no expert but I do have and use a variety of Pre64s including the H&H magnums. I assume you are considering better options, so my offers are off the table and I am out of the equation. Good luck on your project, | |||
|
one of us |
Emory, Got one from an old friend from New Mexico..some emailed me and I didnt reply until today as I have been in the hospital with UTI that went Sepic, thats bad stuff!!but looks like I may have dodged the bullet.. Ray Atkinson Atkinson Hunting Adventures 10 Ward Lane, Filer, Idaho, 83328 208-731-4120 rayatkinsonhunting@gmail.com | |||
|
One of Us |
Ray, Glad that you are doing better, and that you were able to get the correct base. Now if you need another pre-war base, I've got one of those too. I used it many years ago while looking for the right version. I shimmed under the front with a piece of coke can and it seemed to work fine ;> Good hunting, | |||
|
Powered by Social Strata |
Please Wait. Your request is being processed... |
Visit our on-line store for AR Memorabilia