THE ACCURATERELOADING.COM FORUMS


Moderators: Mark
Go
New
Find
Notify
Tools
Reply
  
NECK SIZEING QUESTION
 Login/Join
 
One of Us
Picture of CORNERSTONE
posted
I have never turned necks and was wondering if someone had the time to explain how it is done and the best eqiupment for the job?

This will be on a low volume job. I do reload some, but would it just be better to farm this job out? Is there anyone who does this?


Thanks,
ED
 
Posts: 148 | Location: Pennsylvania, USA | Registered: 08 November 2006Reply With Quote
One of Us
Picture of smedley
posted Hide Post
I have the Forster set up myself. Necker
Works good for me.

Biggest thing to remember is "DON'T TURN THE WHOLE NECK!" you only want to take the "fat" off.


______________________

Smedley

______________________
From Audacity of Hope: 'I will stand with the Muslims should the political winds shift in an ugly direction.'
B.H.Obullshitter
------------------------------------
"Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery"
Winston Churchill
------------------------------------
"..it does not require a majority to prevail, but rather an irate, tireless minority keen to set brush fires in people's minds.." Samuel Adams
------------------------------------
Facts are immaterial to liberals. Twisted perceptions however are invaluable.
------------------------------------
We Americans were tired of being thought of as dumb, by the rest of the world. So we went to the polls in November 2008 and removed all doubt.....let's not do it again in 2012 please.
 
Posts: 3242 | Location: Cruising through the Milky Way at 98,000fps | Registered: 03 October 2005Reply With Quote
one of us
Picture of hivelosity
posted Hide Post
http://www.midwayusa.com/eproductpage.exe/showproduct?

i have a lyman case trimmer it attaches to there case trimmer. and it does a pretty good job.
Like most though you will have to tinker with it.
 
Posts: 2134 | Location: Ohio | Registered: 26 June 2000Reply With Quote
one of us
posted Hide Post
I have the RCBS setup and it does a wonderful job. Follow what has been said and just even up the thickness. My necks have a small area on one side that the cutter does not touch. All you want is an even thickness unless you are forming cases from some other case and the necks are too thick.
 
Posts: 4068 | Location: Bakerton, WV | Registered: 01 September 2003Reply With Quote
One of Us
posted Hide Post
I'm interested in neck turning as well. Do I need any special kind of measuring equipment, or how do you tell how much to cut? Do you need to measure the case neck before and as you are cutting, or how do you know when to stop?
 
Posts: 192 | Registered: 05 September 2005Reply With Quote
One of Us
Picture of smedley
posted Hide Post
If you all are interested go to Varmint Al's and learn how here necking


______________________

Smedley

______________________
From Audacity of Hope: 'I will stand with the Muslims should the political winds shift in an ugly direction.'
B.H.Obullshitter
------------------------------------
"Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery"
Winston Churchill
------------------------------------
"..it does not require a majority to prevail, but rather an irate, tireless minority keen to set brush fires in people's minds.." Samuel Adams
------------------------------------
Facts are immaterial to liberals. Twisted perceptions however are invaluable.
------------------------------------
We Americans were tired of being thought of as dumb, by the rest of the world. So we went to the polls in November 2008 and removed all doubt.....let's not do it again in 2012 please.
 
Posts: 3242 | Location: Cruising through the Milky Way at 98,000fps | Registered: 03 October 2005Reply With Quote
One of Us
Picture of Wink
posted Hide Post
You will need a ball head micrometer to measure neck wall thickness. I am looking for one myself and Mitutoyo is one manufacturer.


_________________________________

AR, where the hopeless, hysterical hypochondriacs of history become the nattering nabobs of negativisim.
 
Posts: 7046 | Location: Rambouillet, France | Registered: 25 June 2004Reply With Quote
One of Us
posted Hide Post
Thanks for the info. One more quick question:
Is this worthwhile on a factory rifle and will I see any noticeable change in accuracy, or is it more beneficial to custom bench rest rifles? I don't want to waste my time trying to polish a turd if its not going to make much of a difference on my factory chamber.
 
Posts: 192 | Registered: 05 September 2005Reply With Quote
one of us
posted Hide Post
My friends at the range that shoot benchrest rifles say that if the chamber is not custom made tight then don't waste your time.
I shoot factory rifles that have been bedded and barrels floated but chambers standard and I shoot .350 groups. I do not turn necks and agree that it would be a waste of time without a custom chamber.
 
Posts: 1159 | Location: Florida | Registered: 16 December 2004Reply With Quote
One of Us
posted Hide Post
Thanks Smiler I was interested in doing it but I think I'll invest in a neck sizer dies for my rifles instead.
 
Posts: 192 | Registered: 05 September 2005Reply With Quote
  Powered by Social Strata  
 


Copyright December 1997-2023 Accuratereloading.com


Visit our on-line store for AR Memorabilia