The Accurate Reloading Forums
need help w/30-06 load

This topic can be found at:
https://forums.accuratereloading.com/eve/forums/a/tpc/f/2511043/m/79910126

03 January 2003, 17:02
kynadog
need help w/30-06 load
I only have a few days to develop a load for a new batch of 165gr. Nosler partitions for my 30-06. I just got invited on a special hunt and would love to hunt with these bullets. Do you guys have any special loads that work for you?

Thanks.
03 January 2003, 17:14
<green 788>
If your rifle won't shoot 57.5 grains of 4350 (either IMR or Hodgdon in this case will do) I would be very surprised.

Look no further. 57.5 grains of 4350 will do it...

Dan
03 January 2003, 17:22
Ku-dude
I checked my data, and agree with 788. My load was 57gr of IMR4350, 210Match primer, shot three round group just at 1" from FC Nickel brass. The velocity was 2942 fps from my 23" barrel. Ku-dude
03 January 2003, 17:47
<bigdog>
Well, just check my data and this last two weeks on my Couse Hunt I use the following load 60 gr. of RL19. The load chrono'd at 2976 fps. I am using the Nosler 165 gr. BT. shooting 1" groups.

I have also had good luck with the Hornady 165 gr Interlock and RL15 or H414, both chrono'd at 2934 fps.

Just my .02 worth

BD
03 January 2003, 17:55
tsturm
quote:
Originally posted by kynadog:
I only have a few days to develop a load for a new batch of 165gr. Nosler partitions for my 30-06. I just got invited on a special hunt and would love to hunt with these bullets. Do you guys have any special loads that work for you?

Thanks.
IMR 4064 46.0g 165g NP CCI 250=2700 fps in 24" BBL .285 three shot groups [Big Grin] [Big Grin]
03 January 2003, 18:08
Coach Hunt
Howdy,

Listen to 788, he's giving good advice. My best load is 57.0 gr. H 4350, 165 Nosler BT, WW cases (matched and fully prepped), Fed. primer. Actually, my rifle shoots 55.5 gr. through 58 gr. to the same point of impact, so I chose 57 as a "happy" medium.

Coach

oh ps..... thanks 788 for the load advice
03 January 2003, 19:27
Lar45
I worked up loads for my son's Rem 721 and my M-98 in 30-06 this past year. We used rem 165 pspcl. For my son's I used rem cases and 61gn RL22 CCI200 primer for 2730fps and .32" group at 100yds. The next group went into .37"! For my M-98 I used win cases and 60gn RL22 for 2770fps and groups around 3/4" for 3 shots at 100yds. My son used these loads to take an Elk and Deer this past fall. The Deer was a one shot kill. The Elk was 250yds running, he held on the front of the chest and the Elk rolled at the shot. It was thrashing around on the ground so he put another one into her. Not bad performance from bulk Rem bullets. I took my deer this year with a .357.
03 January 2003, 20:18
kraky
None of my business but, if you guys are cranking in the mid 2900 fps area with 165's you are running pretty hot loads. You might not see signs of pressure--especially with remington brass but you are "warm".
04 January 2003, 04:17
ricciardelli
Bullet: Sierra 168 Grain Boat Tail Hollow Point
Powder: 56.6 grains of IMR-4350
Primer: Winchester 8-1/2
Case: Winchester
Firearm: Ruger 77R
Velocity: 2801 FPS @ 15' from muzzle
04 January 2003, 06:17
Mule Skinner
The following load works very well in every .30-06 I have had.
Bullet: Nosler 165 Grain Partition
Powder: 57.5 grains of H-4350
Primer: Federal 210
Case: Remington
Firearm: Winchester Pre 64 Model 70 - 24" barrel
Velocity: 2900 FPS @ 15' from muzzle