THE ACCURATERELOADING.COM FORUMS


Moderators: Mark
Go
New
Find
Notify
Tools
Reply
  
Tumbler Suggestions
 Login/Join
 
one of us
posted
Well so far in the last couple of years I have burned up 2 Frankford Arsenal tumblers and one RCBS.
Time for a new one. Any recommendations on a vibratory Tumbler that will last longer than a year or 2?
 
Posts: 1205 | Location: Minnesota | Registered: 07 February 2004Reply With Quote
new member
posted Hide Post
I've had my Lyman for about 12 years. The only thing that went wrong was the goofy rubber plug that let the media out while keeping the cases in the bowl. The plug deteriorated from the heat of being out in my gargage all those years. Hope this helps.

Regards,
BB
 
Posts: 12 | Location: Texas | Registered: 26 March 2007Reply With Quote
One of Us
Picture of woods
posted Hide Post
Hey steve

Hate to be a WA, but just don't buy one. I gave mine away after using another method. Here is a pic of one of my prepped cases and a new case




The prepped case is on the left and the new case on the right. Save a lot of money on tumblers, media and polishing compounds and don't have to worry about media dust cycling through my action and barrel or media getting stuck inside the primer pocket or case. Instant cleaning too, don't have to wait for that tumbler.


____________________________________
There are those who would misteach us that to stick in a rut is consistency - and a virtue, and that to climb out of the rut is inconsistency - and a vice.
- Mark Twain |

Chinese Proverb: When someone shares something of value with you and you benefit from it, you have a moral obligation to share it with others.

___________________________________
 
Posts: 2750 | Location: Houston, Tx | Registered: 17 January 2005Reply With Quote
One of Us
posted Hide Post
Would you be kind enough to tell us what your other method is?
 
Posts: 351 | Registered: 18 September 2004Reply With Quote
one of us
posted Hide Post
quote:
Originally posted by woods:
Hey steve

Hate to be a WA, but just don't buy one. I gave mine away after using another method. .


Sounds great, I'm all ears(or eyes), what's the method you use?
 
Posts: 1205 | Location: Minnesota | Registered: 07 February 2004Reply With Quote
One of Us
Picture of woods
posted Hide Post
quote:
Originally posted by merganser1:
Would you be kind enough to tell us what your other method is?


Get a Lee Zip Trim and a Universal Chuck. Mount the Zip Trim on a piece of 2x4 and clamp it on your bench or in a vise. Spread just a dab of Flitz along the case and spread it with one of those sponges you get in the top of bullet boxes. Spin the case while you are spreading it and put some pressure on it. This is where the Flitz is cleaning and polishing the case. Hold a rag against the case and spin it again. Shinier than new and with a protective coat on it.

Not to mention that with a Cutter and a Case Length Gauge you can trim square and to the same length everytime. Chamfer with the chamfer tool and clean the inside of the neck with some steel wool wrapped around a 22 caliber bore brush.

All those prep steps at the same time and to an amazing consistancy. The only other case prep not done there is the primer pocket cleaning.


____________________________________
There are those who would misteach us that to stick in a rut is consistency - and a virtue, and that to climb out of the rut is inconsistency - and a vice.
- Mark Twain |

Chinese Proverb: When someone shares something of value with you and you benefit from it, you have a moral obligation to share it with others.

___________________________________
 
Posts: 2750 | Location: Houston, Tx | Registered: 17 January 2005Reply With Quote
One of Us
Picture of vapodog
posted Hide Post
My vibro finisher is from Hornady.....I've had it for seven years now and it's still working fine....


///////////////////////////////////////////////////////////////////////////
"Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery."
Winston Churchill
 
Posts: 28849 | Location: western Nebraska | Registered: 27 May 2003Reply With Quote
One of Us
Picture of woods
posted Hide Post
Thought some pictures might help.

cases, trimmer, chamfer tool, flitz, neck cleaner



zip trim with case locked in and trimmer in place



spread flitz



wipe with rag



chamfer



clean inside of neck



one prepped and 4 new cases



____________________________________
There are those who would misteach us that to stick in a rut is consistency - and a virtue, and that to climb out of the rut is inconsistency - and a vice.
- Mark Twain |

Chinese Proverb: When someone shares something of value with you and you benefit from it, you have a moral obligation to share it with others.

___________________________________
 
Posts: 2750 | Location: Houston, Tx | Registered: 17 January 2005Reply With Quote
one of us
posted Hide Post
A powered option instead of the Ziptrim...
 
Posts: 1615 | Location: Washington State | Registered: 27 May 2004Reply With Quote
new member
posted Hide Post
I have a Lyman and a Franford arsenal from Midway. I have had the Lyman for about 10 years with no complaints . I bought the FA one so I could put walnut media in one and corn cob in the other. Both work fine but for the money you could get 2 FA's for the price of most of the others .
My system is to clean my brass in Lyman tuffnut walnut media and to get the heavy stuff off and then in corn cob media with Midway brass polish in it cause the Tuffnut media leaves a lot of rouge on the brass and it builds up in my dies. I use Hornaday one shot lube and resize if FL sizing the back into the corn cob media for a final polish. The final polish is over kill but I like it this way.
 
Posts: 17 | Location: Tuolumne Co | Registered: 10 April 2007Reply With Quote
One of Us
posted Hide Post
I had a Midway for several year, and then the case cracked.. who knows why.. Midway said to send it back in and they would replace it at no charge...

But not wanting to be without a thumbler and considered getting a back up anyway, I ordered a Cabelas, for the same price as the Midway... that was like 4 years ago now...

The Midway is still sitting here collecting dust..

The Cabelas's top is much wider and easier to load and unload...

It has more capacity....

Plus, it is a very very Quiet Thumbler!... I have to sometimes remember I left it on, when I am using it...

My Midway thumbler.. every time I used it, I had to turn up the radio volume quite a bit as it was that distracting...

for the same price.. or even twice the price.. I'd go with another Cabelas, hands down!
 
Posts: 16144 | Location: Southern Oregon USA | Registered: 04 January 2005Reply With Quote
new member
posted Hide Post
I once tried Carnu polish(South-African product) to clean loaded ammo. They were very shiny but I had difficulty opening the bolt even with lower loads. If there is any wax residue the case don't grip the chamber and the bolt takes all the pressure.
After prepping the cases try a mixture of 1 pint of water, 1 lemon's juice and 1 teaspoon of dishwashing liquid. Take the cases out when they are clean enough for you and dry them.
 
Posts: 22 | Location: Rustenburg, South-Africa | Registered: 05 September 2006Reply With Quote
one of us
posted Hide Post
wrongtarget.....

I'm with you - I prefer the Elecktro/Mechanical to the physical/mechanical application, too! I also like the Lee Trimmer Widgets for the Elecktro/Mechanical method. Never could figure out why Lee managed to sell these Motorboat-Starter appliances since most elctrical screwdrivers on Special are a better bargain at the local House Fix-It Store.

I've been using a Lyman 1200 for the past countless years and never experienced an issue; but then again we use 220 volts here in Europe; so we have to order ours separately (thanks Lyman); perhaps the increased voltage affords us 220V users added tumbler life?

Oh, Bye-the-Bye; I'm a retired Procter & Gamble employee, so please use real Bounty Kitchen Roll instead of that generic "cheap-o" imintation so I can afford to go hunting & shooting!


Cheers,

Number 10
 
Posts: 3433 | Location: Frankfurt, Germany | Registered: 23 December 2004Reply With Quote
one of us
posted Hide Post
 
Posts: 4799 | Location: Lehigh county, PA | Registered: 17 October 2002Reply With Quote
One of Us
Picture of woods
posted Hide Post
quote:
Originally posted by Gerry:
wrongtarget.....

I'm with you - I prefer the Elecktro/Mechanical to the physical/mechanical application, too! I also like the Lee Trimmer Widgets for the Elecktro/Mechanical method. Never could figure out why Lee managed to sell these Motorboat-Starter appliances since most elctrical screwdrivers on Special are a better bargain at the local House Fix-It Store.



I have tried it both ways. The Zip Trim spins it faster, has an immediate stop and anti-reverse, there is no torque and no hand fatigue. If it were just the drill without the Zip Trim, I would still be using the tumbler.

JMHO


____________________________________
There are those who would misteach us that to stick in a rut is consistency - and a virtue, and that to climb out of the rut is inconsistency - and a vice.
- Mark Twain |

Chinese Proverb: When someone shares something of value with you and you benefit from it, you have a moral obligation to share it with others.

___________________________________
 
Posts: 2750 | Location: Houston, Tx | Registered: 17 January 2005Reply With Quote
one of us
posted Hide Post
quote:
All those prep steps at the same time and to an amazing consistancy. The only other case prep not done there is the primer pocket cleaning.


EXCEPT for the base/rim of the case. You can't polish the head when it's being held in the shell holder! I did it that way for years before buying my FA/midway tumbler. I just put up with the grungy case heads in contrast to the shiny sides and shoulders of the cases.

I still use the lee system, but AFTER they come out of the tumbler. And I use a cordless drill, or a 1/4 hole shooter. Both spin at high enough RPM to trim quickly.


if you run, you just die tired

It's not that life is so short, it's that death is sooo long!

Speak kindly to me, beloved master. Revel in my unconditional love, and give me every minute that you can spare, for my time with you is short.

Your faithful dog
 
Posts: 596 | Location: Oshkosh, Wi USA | Registered: 28 July 2001Reply With Quote
one of us
posted Hide Post
Without question this is the best.

And someday if you grow tired of handloading you can polish rocks in it. I have a Thumlers and it really is "all that".

http://www.thumlerstumbler.com/vibratory.html
 
Posts: 901 | Location: Denver, CO USA | Registered: 01 February 2001Reply With Quote
one of us
posted Hide Post
I've got the Thumler's #10 and #18. Have had the #18 for at least 10 years with no problems. They are quiet and do an excellent job. They are not cheap.

I had the Midway as a back up to the #18 but couldn't stand the noise.


NRA Life Member
NRA Charter Member Golden Eagles
 
Posts: 899 | Location: South Bend, Indiana | Registered: 11 August 2003Reply With Quote
one of us
posted Hide Post
I needed a Tumbler asap. The Hornady was out of stock everywhere I looked. I went to Cabela's and purchased thier unit. Very quiet and works well, although I don't think it cleans as fast as my RCBS.

I contacted RCBS and asked if I could purchase a new motor. Nope, no money required! They are sending me all the parts I need free of charge. Now that's service!
 
Posts: 1205 | Location: Minnesota | Registered: 07 February 2004Reply With Quote
One of Us
Picture of woods
posted Hide Post
See, no one ever listens to me. Frowner

Oh well, more Flitz for me! clap


____________________________________
There are those who would misteach us that to stick in a rut is consistency - and a virtue, and that to climb out of the rut is inconsistency - and a vice.
- Mark Twain |

Chinese Proverb: When someone shares something of value with you and you benefit from it, you have a moral obligation to share it with others.

___________________________________
 
Posts: 2750 | Location: Houston, Tx | Registered: 17 January 2005Reply With Quote
one of us
posted Hide Post
Don't lift the tumbler while it is operating.I suspect this to have ruined mine.
 
Posts: 11651 | Location: Montreal | Registered: 07 November 2002Reply With Quote
One of Us
Picture of flutedchamber
posted Hide Post
I wore out a Lyman vitrabratory cleaner. Bought the large Dillon and I have had zero problems in the 7 years I have owned it. It is the only cleaner at a reasonable price that cleans 50 caliber cases in quantity.


NRA LIFE MEMBER

You can trust the government. Look how well they took care of the American Indian...

 
Posts: 425 | Location: New Jersey The state sucks, but it's better than living in France. | Registered: 11 July 2005Reply With Quote
one of us
posted Hide Post
I had the lyman plastic see through lid crack on me a couple of times.I changed the bottom part with the motor when my tumbler went and that dodn't cost that much but if it goes again I will try the Dillon.Whatever tumbler you get,I recommend Hornady ONE SHOT tumbler media.She should surely shine those shells!
 
Posts: 11651 | Location: Montreal | Registered: 07 November 2002Reply With Quote
one of us
Picture of Swede44mag
posted Hide Post
I have a Thumblers Tumbler the belt wore out and all of the metal rods have rusted it still works kind of. I have a Midway they had to replace it once so far. I also have a Dillon CV-500 Vibratory Case Cleaner I bought the large version and sent it back to big the the smaller one is just right.

I put crushed walnut shells in the Midway and then switch to the Dillon CV-500 Vibratory Case Cleaner with corn cob and Dillon Polishing media. They are all bright and shiny when I am finished.

BTW I use a Lee Case Length Gage and Shellholder for cleaning and trimming the .223 shells I reload with my Wilson Bench Rest Dies it is not as easy as the Dillon setup but I am not re-loading that many shells. They make ity bity groops with my Remmy XR-100.


Swede

---------------------------------------------------------
NRA Life Member
 
Posts: 1608 | Location: Central, Kansas | Registered: 15 January 2003Reply With Quote
One of Us
posted Hide Post
The new Lyman 2500 Pro Magnum made by Raytech is not bad http://fr.youtube.com/watch?v=NjGQlKyulqU

I use the Dillon 2000 for the BMG
 
Posts: 157610 | Location: Ukraine, Europe. | Registered: 12 October 2002Reply With Quote
  Powered by Social Strata  
 


Copyright December 1997-2023 Accuratereloading.com


Visit our on-line store for AR Memorabilia