THE ACCURATERELOADING.COM FORUMS


Moderators: Mark
Go
New
Find
Notify
Tools
Reply
  
When to get new Brass???
 Login/Join
 
One of Us
posted
Hey guys, I'm about to start reloading some rifle cartridges, which is a new experience for me. I was thinking while I was going through some shotgun hulls the other day, when do you need to discard brass and replace it with new? I shoot a good many shotgun shells and usually shoot 10-20 flats of new stuff every year, so I load them a few times and throw them away. I know if I loaded them enough, they would start to get holes in them near the crimps, split, get the burn marks, etc., but I'm guessing you don't want to reload metallic cartridges until they split or something of that nature...so when should you start loading new brass?


I heal fast and don't scar.
 
Posts: 433 | Location: Monessen, PA | Registered: 23 February 2005Reply With Quote
One of Us
posted Hide Post
Rifle brass is more enduring that shots shells.
I honestly can't give you an answer that is tailored to your shooting. But, I just pay attention to the brass, especially as it work hardens during the loading and firing process and anneal it when it needs it. Case necks will thicken with firings too. If a neck splits during firing, I just pitch it, and keep on loading the brass that hasn't split, even though it has the same number of shots with it as the one that split.
I always measure case length after every firing and after sizing the cases. It does grow long with shooting, and sizing; that's why I measure case length AFTER sizing it. It needs to trimmed to length when it is too long.
Go forth, and load!!! Big Grin

Don




 
Posts: 5798 | Registered: 10 July 2004Reply With Quote
one of us
posted Hide Post
There is no hard and fast rule that bottlenecked rifle brass needs scrapped after X many reloads. It all depends on:

high pressure loads weaken brass faster than milder loads.

full length resizing weakens brass faster than partial full length resizing or just neck resizing.

a big, sloppy chamber will require more resizing (and less case life) than one cut to minimum specs.

some brands of cartridge brass are softer, some are harder than 'normal' which affects case life.

cartridge designs that have a lot of body taper (375 H&H, 22-250 Rem) grow longer on each shot than those with straighter bodies, thus requiring much more frequent trimming to length, which in turn will eventually cause the case head to separate from the body as that area will thin first.

Too many variables to give a blanket response to your question.
 
Posts: 4799 | Location: Lehigh county, PA | Registered: 17 October 2002Reply With Quote
One of Us
posted Hide Post
I throw metallic brass away when the primer starts to seat a little loose. I clean my primer pockets each load using a primer pocket uniformer (brass flows into the primer pocket each firing). When I feel the primer not seating snugly I pitch that brass.
 
Posts: 2627 | Location: Where the pine trees touch the sky | Registered: 06 December 2006Reply With Quote
One of Us
posted Hide Post
Read an article once where someone reloaded brass up to 19 times. Much will depend on how hot you load and how much you work your brass. Interestingly, neck sized only brass fared no better than full sized when lubed properly.
 
Posts: 145 | Registered: 18 July 2006Reply With Quote
one of us
posted Hide Post
When the pockets get loose a drop of nail polish will keep the primers from falling out.
Lyle


"I would remind you that extremism in the defense of liberty is no vice. I would remind you also that moderation in the pursuit of justice is no virtue."
Barry M Goldwater.
 
Posts: 968 | Location: YUMA, ARIZONA | Registered: 12 August 2003Reply With Quote
  Powered by Social Strata  
 


Copyright December 1997-2023 Accuratereloading.com


Visit our on-line store for AR Memorabilia