THE ACCURATERELOADING.COM FORUMS


Moderators: Mark
Go
New
Find
Notify
Tools
Reply
  
The Right Ones...?
 Login/Join
 
One of Us
posted
1- The correct primers for 500 S&W revolver ammo are...?

2- And how about for 375 H&H Belted Mag?

Thanks for the help. Smiler



Jack

OH GOD! {Seriously, we need the help.}

 
Posts: 2791 | Location: USA - East Coast | Registered: 10 December 2005Reply With Quote
One of Us
posted Hide Post
Don't know about the 500, but for my 375 I've always used plain (non mag) 'ol LR's.
 
Posts: 8169 | Location: humboldt | Registered: 10 April 2002Reply With Quote
One of Us
Picture of 900 SS
posted Hide Post
Only magnum primers in my 375, Remington and Federal.
 
Posts: 408 | Location: Bardu, Norway | Registered: 25 August 2007Reply With Quote
One of Us
posted Hide Post
large
 
Posts: 13466 | Location: faribault mn | Registered: 16 November 2004Reply With Quote
one of us
Picture of Ol` Joe
posted Hide Post
Should be listed in you manaul with the load data


------------------------------------
The trouble with the Internet is that it's replacing masturbation as a leisure activity. ~Patrick Murray


"Why shouldn`t truth be stranger then fiction?
Fiction after all has to make sense." (Samual Clemens)

"Saepe errans, numquam dubitans --Frequently in error, never in doubt".



 
Posts: 2535 | Location: Michigan | Registered: 20 January 2001Reply With Quote
one of us
posted Hide Post
Concerning 500 S&W brass. You want to read the following from the Starline brass website:

http://www.starlinebrass.com/i...3487153b3198fc626fb0

quote:

The Initial run of 500 S&W Mag cases was built to use large pistol primer per Smith & Wesson and Cor-bon specifications. On July 28, 2003, Smith & Wesson and Cor-bon changed specification of primer pocket to be large rifle. Rifle primers are same diameter as pistol except they are approximately .006" taller. This was done to prevent primer from being pierced by firing pin when loaded with max loads and heavy bullets (bullets over 400 grains). It was determined that hole in primer allowed pressure to damage firing pin and bushing, kind of like a cutting torch and the harder cup of a rifle primer will prevent occurrence. All cases sold by Starline, Inc. after July 28, 2003, will contain a large rifle primer pocket to accept a large rifle primer. Hodgdon Powder has generated load data which recommends using Win. Large Rifle Primers. Click here to view or call 918-251-5640.

Cor-bon has also tested and recommends CCI 250 primers (Magnum Large Rifle). Our new cases will have an "R" after the "Mag" on head stamp to signify rifle pocket. If you have previously purchased 500 cases without "R" on head stamp and wish to modify, you can use a large rifle pocket uniformer to deepen primer pocket to accept large rifle primers by deepening pocket approximately .006". This will not affect integrity of case. For concerns regarding situation contact Smith & Wesson or Cor-bon as they designed case and subsequently changed it.



In short uniform all of your 500 S&W brass with a RIFLE primer pocket uniformer and then use either large rifle or large rifle magnum (cci 250) primers depending on which primer your loading data used...............................DJ


....Remember that this is all supposed to be for fun!..................
 
Posts: 3976 | Location: Oklahoma,USA | Registered: 27 February 2004Reply With Quote
One of Us
posted Hide Post
Thanks, I looked at my Hornady brass
and it's marked L R so large rifle it is.
{I'm referring to 500 S&W}



Jack

OH GOD! {Seriously, we need the help.}

 
Posts: 2791 | Location: USA - East Coast | Registered: 10 December 2005Reply With Quote
  Powered by Social Strata  
 


Copyright December 1997-2023 Accuratereloading.com


Visit our on-line store for AR Memorabilia