THE ACCURATERELOADING.COM FORUMS

Accuratereloading.com    The Accurate Reloading Forums    THE ACCURATE RELOADING.COM FORUMS  Hop To Forum Categories  Guns, Politics, Gunsmithing & Reloading  Hop To Forums  Reloading    Is there a problem in forming 3006 brass and using it for 270win??

Moderators: Mark
Go
New
Find
Notify
Tools
Reply
  
Is there a problem in forming 3006 brass and using it for 270win??
 Login/Join
 
one of us
posted
270win was originally made from 3006 cases. That much I know already. So I thought I could use some of my old once fired 3006 cases in my 270win, just for plinking, once, and then throw the case away. Is anyone doing this? Any problems in that?

Any contribution is wellcomed
Niels
 
Posts: 389 | Location: Denmark | Registered: 05 May 2002Reply With Quote
one of us
Picture of Fjold
posted Hide Post
Not a problem. I've necked 308's down to 243 before. You just get a thicker neck which will probably help the accuracy since the factory chambers are usually cut so big. Make sure that the neck is not too thick and shoot away.


Frank



"I don't know what there is about buffalo that frightens me so.....He looks like he hates you personally. He looks like you owe him money."
- Robert Ruark, Horn of the Hunter, 1953

NRA Life, SAF Life, CRPA Life, DRSS lite

 
Posts: 12754 | Location: Kentucky, USA | Registered: 30 December 2002Reply With Quote
Moderator

Picture of Mark
posted Hide Post
Might want to use them more than once, they might shoot better the second loading.


for every hour in front of the computer you should have 3 hours outside
 
Posts: 7776 | Location: Between 2 rivers, Middle USA | Registered: 19 August 2000Reply With Quote
One of Us
Picture of vapodog
posted Hide Post
Just a little warning...if you use military brass for the 30-06 in your 270 reduce the starting loads quite a bit....they are typically heavier and have less combustion room.


///////////////////////////////////////////////////////////////////////////
"Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery."
Winston Churchill
 
Posts: 28849 | Location: western Nebraska | Registered: 27 May 2003Reply With Quote
One of Us
Picture of cal30 1906
posted Hide Post
I have been doing it for years.


The question is does it create premature

Throat erosion??


My speer loading manual #1 says it does bewildered

I never noticed and continue the practice...


Don




If it cant be Grown it has to be Mined! Devoted member of Newmont mining company Underground Mine rescue team. Carlin East,Deep Star ,Leeville,Deep Post ,Chukar and now Exodus Where next? Pete Bajo to train newbies on long hole stoping and proper blasting techniques.
Back to Exodus mine again learning teaching and operating autonomous loaders in the underground. Bringing everyday life to most individuals 8' at a time!
 
Posts: 3082 | Location: Northern Nevada & Northern Idaho | Registered: 09 April 2005Reply With Quote
one of us
posted Hide Post
quote:
Originally posted by cal30 1906:
I have been doing it for years.


The question is does it create premature

Throat erosion??


My speer loading manual #1 says it does bewildered

I never noticed and continue the practice...


Don


Hmm... Did the manual say why that should cause throat erosion?
 
Posts: 389 | Location: Denmark | Registered: 05 May 2002Reply With Quote
One of Us
Picture of jocamp64
posted Hide Post
Excessive case neck thickness can cause excessive pressure if it crimps the bullet when chambered.

This is unlikely going from .308 to .277 but it is a concern that should be addressed for safety.


"Untutored courage is useless in the face of educated bullets." George S Patton.
 
Posts: 38 | Location: North Texas | Registered: 20 August 2005Reply With Quote
one of us
posted Hide Post
Your formed .270's will be slightly short, since the '06 is very slightly shorter than the .270 (2.495" vs. 2.54"). This is of minimal consequence because the '06 case will be very slightly lengthened when squeezed down to .277 and the expander button pulled back through the neck, so it will end up just about the "trim to" length for a .270.

Your necks will also be a tad thicker, but as mentioned early, few .270 chambers do not benefit from a thicker neck. If yours is a rare tight chamber, you might need to turn the necks, but it is doubtful. DO chamfer the insides of the necks to assure seating the bullets without shaving jacket material.

The great advantage of forming .270 from '06 brass is that you can control the placement of the shoulder. Screw your FL die into the press just to the point that the resized brass chambers with a tiny bit of resistance felt as you turn down the bolt. This will mean that your headspace is perfectly adjusted for your chamber and will mean minimum case stretching and maximum case life. This is especially useful if you have a chamber that is slightly long (the dreaded and typically misunderstood "excessive headspace").
 
Posts: 13263 | Location: Henly, TX, USA | Registered: 04 April 2001Reply With Quote
One of Us
posted Hide Post
I necked a bunch of my old 30-06 brass down to 25-06 without a problem. I necked down and them trimmed them before loading.
 
Posts: 428 | Location: Bozeman, MT | Registered: 04 January 2005Reply With Quote
  Powered by Social Strata  
 

Accuratereloading.com    The Accurate Reloading Forums    THE ACCURATE RELOADING.COM FORUMS  Hop To Forum Categories  Guns, Politics, Gunsmithing & Reloading  Hop To Forums  Reloading    Is there a problem in forming 3006 brass and using it for 270win??

Copyright December 1997-2023 Accuratereloading.com


Visit our on-line store for AR Memorabilia