THE ACCURATERELOADING.COM FORUMS


Moderators: Mark
Go
New
Find
Notify
Tools
Reply
  
AA 5744 loading data for 458 Lott
 Login/Join
 
One of Us
posted
Anyone have any or know where I can find loading data for using AA 5744 in the 458 Lott ?
 
Posts: 122 | Location: Villa Rica, GA. | Registered: 27 June 2003Reply With Quote
One of Us
Picture of KennethI
posted Hide Post
Accurate Powder has a feature where you can submit a request for data. I have done it several times; they were very helpful each time.
 
Posts: 238 | Location: Southern California | Registered: 22 November 2004Reply With Quote
One of Us
posted Hide Post
while not a 458 lott i use 35 grains in a 470 with a 500 gr cast bullet. I believe the velocity is in the 12-1500 FPS range. i think your lott would be similar
 
Posts: 13466 | Location: faribault mn | Registered: 16 November 2004Reply With Quote
one of us
Picture of Hog Killer
posted Hide Post
tank, just send Accurate Powder your request, for bullet and velocity wanted. They are very helpful. Best to get it from the "horse's mouth".

Keith


IGNORE YOUR RIGHTS AND THEY'LL GO AWAY!!!
------------------------------------
We Band of Bubbas & STC Hunting Club, The Whomper Club
 
Posts: 4553 | Location: Walker Co.,Texas | Registered: 05 September 2003Reply With Quote
One of Us
posted Hide Post
I sent them an email and submitted their online data request form 6 days ago and no response yet. How long has it taken them to respond when you have requested info in the past ?
 
Posts: 122 | Location: Villa Rica, GA. | Registered: 27 June 2003Reply With Quote
One of Us
posted Hide Post
I got a response today. I had requested info for two different powders (5744 and 2200) Here is the info if anyone else may need it.

Unfortunately we do not have any specific lab tested data on this caliber. (See notes 1.1 and 2.1 below).

However, we can provide you with some guideline, based on calculations and information from other sources.

Caliber: .458Lott.

Application: Rifle.

Barrel length: 24â€

Reduced loads:

Powder: Accurate -- 5744.

Bullet weight: 300grains.

Low load: 47.0 grains (1900 – 2000 ft/p/sec).

Max load: 68.0 grains (2600 – 2700 ft/p/sec) Max pressure!!

Bullet weight: 350grains.

Low load: 44.0grains (1800 – 1900 ft/p/sec)

Max load: 63.0 grains (2450 – 2550 ft/p/sec). Max pressure!!

Bullet weight: 400 grains.

Low load: 42.0grains (1750 – 1850 ft/p/sec)

Max load: 61.0 grains (2300 – 2400 ft/p/sec). Max pressure!!

Bullet weight: 500grains.

Low load: 38.0grains (1500 – 1600 ft/p/sec)

Max load: 54.0 grains (1500 – 1600 ft/p/sec). Max pressure!!



Powder: Accurate -- 2200.

Bullet weight: 350grains.

Start load: 74.0grains (2500 – 2600 ft/p/sec)

Maximum load: 83.0 grains (2600 - 2700ft/p/sec) Max pressure!!.

Bullet weight: 400grains.

Start load: 71.0grains (2300 – 2400 ft/p/sec)

Maximum load: 79.0 grains (2450 – 2550 ft/p/sec) Max pressure!!.

Bullet weight: 500grains.

Start load: 68.0grains (2100 – 2200 ft/p/sec)

Maximum load: 75.0 grains (2250 - 2350ft/p/sec) Max pressure!!.

NOTE:

It’ important to note that:

Whenever Western powders Inc do not test, and have actual data, on a particular caliber or caliber/bullet combination, we may in some cases provide some guideline. This information will be based on various procedures and calculations, or from other very reliable sources.

1. SAFETY is our prime concern therefore:

1.1. The loading data is conservative, especially regarding the minimum or start load to ensure a safe baseline to work from.

1.2. The safety margin built into the start load might be more than the customary 10%.

2. We strongly recommend.

2.1. To always start at the recommended minimum “START†load.

2.2. If at all possible, measure the velocity.

2.3. Contact us again with the velocity data, so that we can verify, and correlate with our calculated/estimated data. The data should also be compared, with the typical velocity levels accepted in the industry, for that particular caliber-bullet weight combination.





Regards

Johan Loubser

Ballistician

Western/Accurate Powders

Tel: 1800 497 1007 or (406) 234 04 22

Part of Western Powders -- Miles City Montana

For all Sales, Marketing, Pricing Distribution and related issues, please call toll free 800-497-1007.



To ensure a continuous record per subject/issue, please use the "REPLY" function.



IMPORTANT NOTE: Allways begin loading from the minimum "START charge and carefully develop loads by increasing in small increments of 2% towards the Maximum load.

Western Powders Inc. disclaims all possible liability for damages including, actual, incidental and consequential, resulting from usage of the information or advice contained in this message.

Use the data and advice at your own risk, and with extreme caution.

We also request that you visit our website at www.accuratepowder.com for more comprehensive information.

DISCLAIMER:

This communication is confidential and may be legally privileged. If you are not the intended recipient,

(i) please do not read or disclose to others, (ii) please notify the sender by reply mail, and (iii) please

delete this communication from your system. Failure to follow this process may be unlawful. Thank you for your cooperation.
 
Posts: 122 | Location: Villa Rica, GA. | Registered: 27 June 2003Reply With Quote
  Powered by Social Strata  
 


Copyright December 1997-2023 Accuratereloading.com


Visit our on-line store for AR Memorabilia