THE ACCURATERELOADING.COM AFRICAN HUNTING FORUM

Accuratereloading.com    The Accurate Reloading Forums    THE ACCURATE RELOADING.COM FORUMS  Hop To Forum Categories  Hunting  Hop To Forums  African Big Game Hunting    Re: How to properly work a Mauser-type bolt?

Moderators: Saeed
Go
New
Find
Notify
Tools
Reply
  
Re: How to properly work a Mauser-type bolt?
 Login/Join
 
one of us
posted
I have never seen anyone work a bolt action rifle as fluidly, efficiently, or as quickly as Allen Day. Some people talk it, but I know he can walk it.

Chuck
 
Posts: 2659 | Location: Southwestern Alberta | Registered: 08 March 2003Reply With Quote
one of us
Picture of Will
posted Hide Post
Now, talk we got.
 
Posts: 19392 | Location: Ocala Flats | Registered: 22 May 2002Reply With Quote
one of us
Picture of Will
posted Hide Post
Cold Bore,

I think you have it figured out.

When charged by dangerous game, that bolt is flying, and survival is more important than technique, and it better work without binding, no matter what.
 
Posts: 19392 | Location: Ocala Flats | Registered: 22 May 2002Reply With Quote
one of us
posted Hide Post
I tried the same rapid cycling technique on a Rem 700, push feed M70 and Ruger 77MkII and when applying upward or sideways "torque" to the bolt handle at the rear of the stroke they too will bind up although not as bad with the Rem. Looks like some practice is in order. I must say that I haven't had this issue with my 7600 or lever gun
Thanks again.
 
Posts: 46 | Registered: 16 September 2004Reply With Quote
<allen day>
posted
Now there's a textbook lesson for you!

AD
 
Reply With Quote
one of us
posted Hide Post
.
 
Posts: 7857 | Registered: 16 August 2000Reply With Quote
one of us
posted Hide Post
Picture from the Winchester manual.

 
Posts: 5543 | Registered: 09 December 2002Reply With Quote
One of Us
Picture of jorge
posted Hide Post
Kurt C: You are correct sir on the British method, primarily because the SMLE is a cock-on-closing action and the bolt handle to trigger geometry lends itself to very rapid fire. Now to retort on the folks with insecurities, amazing how the push feed crowd feels so inadequate they have to veer off the subject in order to justify their choices. They still haven't answered the central question as to why PHs prefer and recommend Mauser type actions and Allen's technique on bolt operation. jorge
 
Posts: 7151 | Location: Orange Park, Florida. USA | Registered: 22 March 2001Reply With Quote
one of us
posted Hide Post
This thread is funny!! The rifle is a piece, and needs fixed or better yeat replaced with a M700! Then you have a couple of apes trying to tear the bolt out of the top of the gun to boot!!



Why are you pushing up on the bolt handle? Is it going to fall out of the gun if you don't.



I suggest you stick with pumps or lever actions.



Kent
 
Posts: 116 | Location: Cleves, IA | Registered: 14 July 2003Reply With Quote
one of us
posted Hide Post
Quote:

Quote:

When I work a Mauser-type rifle, I don't actually grasp the bolt knob. I bring my hand up with the inside edge

What exact part of your hand? Be specific.

slapping the bolt handle up smartly, then I turn the palm sightly up and slap the bolt handle back smartly (the hand goes with it and follows thru as a guide) clear to the end of it's travel when it meets the bolt stop, then I slap it ahead fully with the hand

Again what specific part of your hand? What are you fingers doing at this time? following thru, then down smartly. I do this very quickly, in one fluid motion, and the entire cycle takes just a split second.

AD


 
Posts: 5543 | Registered: 09 December 2002Reply With Quote
  Powered by Social Strata  
 

Accuratereloading.com    The Accurate Reloading Forums    THE ACCURATE RELOADING.COM FORUMS  Hop To Forum Categories  Hunting  Hop To Forums  African Big Game Hunting    Re: How to properly work a Mauser-type bolt?

Copyright December 1997-2023 Accuratereloading.com


Visit our on-line store for AR Memorabilia

Since January 8 1998 you are visitor #: