THE ACCURATERELOADING.COM GUN CLEANING FORUM

Go
New
Find
Notify
Tools
Reply
  
Need Your Ultrasonic Gun Cleaning Input
 Login/Join
 
new member
posted
I’m thinking about purchasing a small RCBS or Lyman ultrasonic cleaner and the parts cleaning solution for occasional deep cleaning of field-stripped pistols. Some of the threads I’ve read on the topic in this forums have raised question/concerns I hope you can address.

1) Will ultrasonics effectively internally clean a field-stripped (not detail disassembled) frame and slide?
2) will this process damage anodized aluminum?
3) will it damage applied coatings - ceracoat, duracoat, Beretta bruniton, CZ polycoat, etc? Any other finishes known to be damaged?
4) how about damaging the white or red dots on sights, safeties, etc?
5) any other pitfalls/show-stoppers you’ve uncovered?

Thanks in advance for sharing your experience.

Best, Jeff
 
Posts: 12 | Location: USA | Registered: 06 June 2020Reply With Quote
one of us
posted Hide Post
The one I have states that you are supposed to remove some things more than just a field strip - like removing the grip panels.

You need compressed air if you are not going to detail strip.

That said, mine has not damaged the finish of a glock, SIG, or Beretta factory pistols, with the solutions I have used. The solution is the big issue.
 
Posts: 6998 | Location: Minnesota USA | Registered: 15 June 2007Reply With Quote
one of us
Picture of muzza
posted Hide Post
I have one that I use to clean motorcycle carburetors
and associated other parts , as well as rifle bolts , trigger groups etc. I have never had any issue with surface finishes being damaged or affected in any detrimental way


________________________

Old enough to know better
 
Posts: 4375 | Location: Eltham , New Zealand | Registered: 13 May 2002Reply With Quote
new member
posted Hide Post
Thanks for you input fellers. The shooting range where I work bought a large commercial unit several months back aNd subsequently damaged the coating on a Browning 1911 380 and a Ruger 38 Spec in it. Sooo, I’m a bit reluctant to jump in. I’m considering a Lyman unit and Lyman firearms cleaner so I think I’ll ask them to comment. Thanks again for your advice.

Jeff
 
Posts: 12 | Location: USA | Registered: 06 June 2020Reply With Quote
one of us
posted Hide Post
I have the Hornady 1.2 liter. I only clean(ed) brass with it once upon a time. I found it didn't clean anywhere near as well as a tumbler with pins.

I've never considered tossing in a stripped handgun as I would rather hand clean them.

I would save the bucks unless you are cleaning lots of brass, but sounds like you have that covered at work.


___________________

Just Remember, We ALL Told You So.
 
Posts: 22442 | Location: Occupying Little Minds Rent Free | Registered: 04 October 2012Reply With Quote
Administrator
posted Hide Post
We actually do clean stripped handguns in an ultrasonic cleaner.

We have one with a tank that is about 2 feet long.

We use WD40 as the cleaning media, and it works great.

We take off anything that is not metal, and so far had no problems at all, and it cleans very well.


www.accuratereloading.com
Instagram : ganyana2000
 
Posts: 57675 | Location: Dubai, UAE | Registered: 08 January 1998Reply With Quote
one of us
Picture of Jiri
posted Hide Post
How do you process your Glocks? ;-)
 
Posts: 1804 | Location: Czech Republic | Registered: 22 May 2002Reply With Quote
  Powered by Social Strata  
 


Copyright December 1997-2021 Accuratereloading.com


Visit our on-line store for AR Memorabilia