Troll Alert!!

This person may mascarde as a Doctor, as a all knowing gunsage, as the amazing field experience of Bell and Boddington, and that, frankly, it says it's female!!!

Oh, yeah, and can gumsmit' a 585 nayti in a remington model 700 ... no, wait, that was another of it's persona

Notice the high quality photos of it's own hunts, guns, and target.... no, wait,,, that would be a serious poster, not POSER

Thanks jeffeosso. I did a little searching here and I found the troll in his street clothes!

Follow the link.

http://www.nookhill.com/ubb/ultimatebb.php?ubb=get_topic;f=16;t=002743#000005

Funny part is this is none other than jeffeosso!

I think the troll is self-destructing.

<edited for political correctness>

Show us PROOF, Judy. Make one!

Jeffe

[ 10-07-2003, 01:09: Message edited by: jeffeosso ]

I've taken the feedback from other members, and will tone it down.

I have a new slogan for the troll, though

Show us PROOF, Judy. Make one!

jeffe

Make WHAT, jeffe--a baby troll???? WTF?

DAMN!!! I seen that once when drinking 33 or Boones Farm, hmm can't remember

Hey, Judy, I've been to Jeffe's home and seen his rifles and his work. Haven't seen anything of yours pictured here. I'm sure there is a good reason?

I'm sure we can supply you an Rem 700 action so you can show us how it is done.

old post I made

quote:

---

Originally posted by Bill Leeper:
Thomas,
I said "nameless"! Another guy had a setup so he could chamber on a drill press. Again, he turned out some surprisingly good work. Regards, Bill.

---

yeah, that's it.. i am going to sell my lathe and just use my firestorm cordless and saw-zal. yeahyeah.. i can put the barrel in a pipe vise, like indexing it, and cut the threads with a bimetal blade.. and if I run it fast enough, it'll polish the threads... yeahyeah... and mymymmymymy firestorm, well, i'll need another battary, as the 9.6's just get too hot too fast, and you can't use the same finish reamer to start the hole.. and I've got some bacon fat to lube it... should be fine... and then I can just stick the receiver in the freezer and the barrel over the stove, till the threads get red hot, and then use my pipe wrench to fuse em together.. dont need to rosin or nuttin..

Hell, if the thread wont work, my brother in law's (that's my first cousin) has a pipe rig on his truck and we can just bore em both to waterpipe threads... he's got a torch, so we can anneal that hard barrel and action, and they'll fit right togehter.y

yeahyeaheayh... and we'll use a remington action for my 505 gibbbs based 270... it's the 277 whitetailfromamile,, shooting 110 gr at 4200 fps... gotta be barnes bullets though.. them lead jacketed thangs just make a blue mist on the way down the range..

hey, i found a tasco 6x24 when I was picking up trash, for the county, know-what-i-mean, just a little bent, so I put it back in my pipe vise and tapped it back pretty striaght... I used the handle of my sledgehammer as a guide and tweeker..

Oh, yeah.. and for tapering the barrels, I'll start with a pacnor blank, and take my firestorm drill, and beat 2 horseshoin nails into the ends... set one end IN a cigerette putter outer thumbnul..(my wife thinks its so high class to have one of these in her nearly antique macdonalds aluminim ashtrays) and the other chucked into my cordless.. and take my beltsander to cut away the taper... yeehaa... just use that ole seldgehammer handle for a guide....

damn it.. this would have been even funnier if BBB had done it.