The Accurate Reloading Forums
Removing the front sight band from a CZ550

This topic can be found at:
https://forums.accuratereloading.com/eve/forums/a/tpc/f/4711043/m/158102004

08 January 2006, 01:32
woodsracer
Removing the front sight band from a CZ550
Does anyone know how to remove the front sight band off of a CZ550 Safari Magnum? bewildered


"They who would give up an essential Liberty for Temporary Security, deserves neither Liberty or Security." ---Benjamin Franklin


"SIC SEMPER TYRANNUS"
08 January 2006, 01:37
RIP
With a vice, a torch, and a mallet.
08 January 2006, 04:40
woodsracer
quote:
Originally posted by RIP:
With a vice, a torch, and a mallet.


SOOOOOO, it is soldered on? bewildered Are ya sure??? Wink


"They who would give up an essential Liberty for Temporary Security, deserves neither Liberty or Security." ---Benjamin Franklin


"SIC SEMPER TYRANNUS"
08 January 2006, 06:03
Mike Birdwell
It is soldered on, I removed the one on my 458 lott to install a barrel swivel band. I just heated with a torch & tapped off with a wood mallet. Re-heated to re-install it.

Regards Mike


Whiskey for my men & beer for my horses
08 January 2006, 06:17
woodsracer
quote:
Originally posted by Mike Birdwell:
It is soldered on, I removed the one on my 458 lott to install a barrel swivel band. I just heated with a torch & tapped off with a wood mallet. Re-heated to re-install it.

Regards Mike


As is common, RIP knows his stuff. I should have known, I just wanted a second opinion. Wink


"They who would give up an essential Liberty for Temporary Security, deserves neither Liberty or Security." ---Benjamin Franklin


"SIC SEMPER TYRANNUS"
08 January 2006, 07:22
450 RIGBY
Right. It is soldered. I removed it from my 4 CZ Safaris to install Talley bands. I use kitchen electric range. Make sure you not overheat it. Blackening could change color. I check temperature by touching sitht with with piece of soldering wire and as soon wire will start to melt after contact I knock it off with some hard wood dowell and hammer. I make wery fine line accross joint of sight band and barrell as reference line before start to heat it to make sure I install it lined up exactly the same way as it was otherwise you change point of aim of express sitht. Sight is so tall, slight missalignement will force you to shift rear sight way to the one site. It just looks bad.
08 January 2006, 08:15
woodsracer
quote:
Originally posted by 450 RIGBY:
Right. It is soldered. I removed it from my 4 CZ Safaris to install Talley bands. I use kitchen electric range. Make sure you not overheat it. Blackening could change color. I check temperature by touching sitht with with piece of soldering wire and as soon wire will start to melt after contact I knock it off with some hard wood dowell and hammer. I make wery fine line accross joint of sight band and barrell as reference line before start to heat it to make sure I install it lined up exactly the same way as it was otherwise you change point of aim of express sitht. Sight is so tall, slight missalignement will force you to shift rear sight way to the one site. It just looks bad.


THANKS!!!! That's great info. thumb


"They who would give up an essential Liberty for Temporary Security, deserves neither Liberty or Security." ---Benjamin Franklin


"SIC SEMPER TYRANNUS"
08 January 2006, 08:23
tiggertate
Pencil lead will prevent solder from flowing onto places you don't want it. Just take a #2 and scribble all around the joint.


"Experience" is the only class you take where the exam comes before the lesson.
08 January 2006, 20:44
woodsracer
quote:
Originally posted by tiggertate:
Pencil lead will prevent solder from flowing onto places you don't want it. Just take a #2 and scribble all around the joint.


Another great piece of info; I LOVE this place!!! Cool


"They who would give up an essential Liberty for Temporary Security, deserves neither Liberty or Security." ---Benjamin Franklin


"SIC SEMPER TYRANNUS"