The Accurate Reloading Forums
The "hole in my safe" - what next?
25 September 2010, 20:17
rnoviThe "hole in my safe" - what next?
Ok, so if I were to go with a 300 H&H, what would be the best build process? Pre-64 Winnie Action from the factory, but already cut as a 300? Start with a used .375 H&H action and rebarrel?
If I went with an older rifle, I'm likely looking at a big restocking project - which is fine. I like wood!
Thoughts?
Regards,
Robert
******************************
H4350! It stays crunchy in milk longer!
25 September 2010, 21:28
ledvmquote:
Pre-64 Winnie Action from the factory, but already cut as a 300?
Yes...start there and work up. If you look...you can find one!
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
J. Lane Easter, DVM
A born Texan has instilled in his system a mind-set of no retreat or no surrender. I wish everyone the world over had the dominating spirit that motivates Texans.– Billy Clayton, Speaker of the Texas House
No state commands such fierce pride and loyalty. Lesser mortals are pitied for their misfortune in not being born in Texas.— Queen Elizabeth II on her visit to Texas in May, 1991.
25 September 2010, 21:29
ledvmquote:
If I went with an older rifle, I'm likely looking at a big restocking project
Why???
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
J. Lane Easter, DVM
A born Texan has instilled in his system a mind-set of no retreat or no surrender. I wish everyone the world over had the dominating spirit that motivates Texans.– Billy Clayton, Speaker of the Texas House
No state commands such fierce pride and loyalty. Lesser mortals are pitied for their misfortune in not being born in Texas.— Queen Elizabeth II on her visit to Texas in May, 1991.
25 September 2010, 21:40
rnoviThat's a fair point on the restocking.
Regards,
Robert
******************************
H4350! It stays crunchy in milk longer!
25 September 2010, 22:49
MileHighShooterP-64 if you put in the time looking for a rifle.
Or you can use any M70 Classic. I have one in 270 and was quoted about 200$ to open the bolt face, change the bolt stop and remove the magazine block to make it full length.
These can be had around 5-700$
One could also do the same with a CZ550. If you wanted to start from scratch you can buy CZ550 actions from Midway and I think Brownells, just get a magnum length box with a .532 bolt and you're good to go.
I love the 300 Win, its a great cart. But you have a safe full of CLASSIC carts like the 7x57 and 375. Put another one in there to keep them company

If you think every possible niche has been filled already, thank a wildcatter!
28 September 2010, 23:51
WhatTheHow about a 111 Savage TH in 25-06...

29 September 2010, 07:41
rnoviquote:
Originally posted by WhatThe:
How about a 111 Savage TH in 25-06...

Already got a Rem. M7MS in .257 Roberts.

My namesake...how could I not?
Regards,
Robert
******************************
H4350! It stays crunchy in milk longer!
29 September 2010, 07:50
RaySenderoHere ya go! Winchester M70 Supergrade:
http://www.winchesterguns.com/...mily=001C&mid=535107Take your pick - 270, 30/06 or 300WM
________
Ray
30 September 2010, 10:39
rnoviOk, so I DID buy a rifle! Just put some money down on one!
And since it's going to take 10 days to get here (/sigh) we can all play 20 questions!
First hint: Yes, it's used.

Regards,
Robert
******************************
H4350! It stays crunchy in milk longer!